1022 Wall Pulley
Clean design minimizing weight while increasing strength. Sheave diameter of 1 inch easily accommodate ropes from 8 to 11 mm. Oilite bushing. Strength 7875 lbf. (35kN).

1023 2 Inch Prusik Minding Pulley
Designed for strength and durability. Unique side plate design which keeps the rope from rubbing on any surface which comes in con­tact with the pulley. Sheave diameter of 2 inches. Accommodates ropes from 9 to 13 mm. Oilite bushing. Strength 9000 lbf. (40kN).

1019 2.5 inch Prusik Minding Pulley
Highly efficient swing-sided prusik minding pulley. Large diameter sheave mounted on sealed ball bearings for high efficiency. Great for high-strength applications and arborists. Fits up to 1/2 inch ropes. Strength 10,125 lbf. (45kN).

RSI Pulleys
Lightweight, strong, swing sideplate pulleys for work and rescue. Available in Oilite® bushing or sealed bearing versions.

6101 RSI Haul Safe
Hauling and raising pulley with built in cam safety grab. The 4:1 unit provides the ideal mechanical advantage for manhole and vessel extraction. Once attached to a rigging point and worker is properly secured with safety cam engaged, unit works as a hauling system with a deadman's safety. Even if the hauling team is incapacitated, the victim is secure and will not fall. Works with the cam before the sheave to allow much greater direction of pull on haul line. The cam can be locked open with the safety pin to use the Haul Safe as a double sheave pulley. Exceeds all appli­cable NFPA, OSHA, ANSI and CSA standards. Designed for 7/16 inch rope and will accept 1/2 inch ropes. Strength 10,000 lbf. (44kN).

6131 RSI Hollowshaft Pulley
This pulley is a breakthrough in pulley design. It has the highest strength to weight ratio in the industry. Large 3.5 inch sheave fits ropes up to 5/8 inch in diameter. Exclusive tri-lobe rigging hole fits 3 large rescue carabiners. The huge 2 inch bush­ing provides the highest efficiency avail­able. The 1.75 inch bore of the axle allows extra large carabiners, slings, ropes, etc. to fit through the center of the pulley. Strength 10,000 lbf. (44kN).

6230 SMC Swiftwater Pulley
Designed to fulfill the requirements of swiftwater rescue. This super lightweight pulley features a 2 inch sheave. Anodized side plates feature holes that help to minimize the hydroplaning effect that may occur with a typical pulley and are shaped to maxi­mize the effectiveness of a prusik hitch. The top hole accepts 2 large rescue carabiners and allows them to rotate freely. Weight 6 oz.

• Strength 7650 lbf. (34kN)
• Sealed ball bearings

6235 SMC Kootenay HX Pulley
The Kootenay HX from SMC is the most advanced compact knot passing pulley on the market. Aluminum side plates with a high-strength aluminum sheave. Sealed ball bearings provide optimal efficiency. The primary carabiner hole accepts numerous rescue carabiners. Secondary carabiner holes are provided for use with tag or belay lines. Two quick-release pins lock off the sheave when a high strength tie-off is required. Adding to its versatility, the Kootenay HX may also serve as an edge roller for rope protection. Weight 1 lb. 9 oz.

• 8.5 inches x 4.4 inches x 3 inches
• Anodized aluminum
• Sealed ball bearing
• Manufactured entirely in the USA

Yates Mountain Lite Pulleys
Sealed bearing prusik minding pulleys designed to maximize strength while reducing weight. A new standard for high strength, lightweight pulleys. Weight reduction of up to 35% over pulleys of similar size. Designed specifically for mountain rescue and USAR applications when a lightweight, NFPA G classified pulley is needed. Made using aircraft quality aluminum, this design features a 2.5 inch sheave (full, true 2 inch tread diameter). Unique channel milled into the side of the sheave reduces the effect of debris building up between it and the side plate. Side plate design allows the use of larger ropes in a compact pulley. Manufactured exclusively for Yates by SMC. UL classified to meet NFPA 1983/2006 edition standards.
Strength 8100 lbf. (36kN) Weight 8.5 oz. single, 15 oz. double.

6210

single

Red

6215

single

Black w/Black Sheave

6220

double

Blue

6225

double

Black w/Black Sheaves

Rock Exotica Omni Blocks®
The Rock Exotica Omni Blocks combine a swivel with a ball bearing pulley. These pulleys eliminate twisting and simplify your rope rigging system and save valuable vertical height compared to a conventional puley/carabiner/swivel combination. Each precision machined aerospace alloy block has a unique button-activated release feature that allows instant access to the sheave for midline attachment. The milled alloy attachment eye is large enough to accept most carabiners and snaps. 1.5 inch tread diameter pulley accepts up to 1/2 inch rope. Strength is 8100 Ibf. (36 kN). Made in USA.

6300

Single Sheave

6310

Double Sheave

6320 Rock Exotica
Omni Aztek Elite® Blocks Developed by Ropes that Rescue Ltd. these blocks, configured as set-of-fours will enable the user great versatility in a personal mechanical advantage system suitable for rescue and general rigging. Hewn from a solid block of high strength aluminum and engineered to withstand over 8,000 lbf. (36kN). The set of two blocks are different colors for ease of identification. One way you have a 5:1 mechanical advantage. Turn it around and a 4:1 w/change of direction is the result. The progress capture ratchet prusik can be attached at either end. One quick pin is sold with each set of blocks. Additional pins may be purchased separately.

(C) Anchor Rings
Useful for many rigging and rescue applications. Drop forged alloy steel. Small strength 5000 lbf. (22kN). Large strength 10,000 lbf. (44kN).

7600

3/8 inch x 2.25 diameter

7800

1/2 inch x 3 diameter

(D) Forged Anchorage
Multi-directional load anchorage. Available with 1/2 inch threaded stud or open hole configuration. Minimum use of Grade 8 bolt is required. Strength 5000 lbf. (22.2kN).

1070

Standard

1075

w/Threaded Stud

(A) 1026 BW Large Aluminum 8
Original design figure eight has many uses in work and rescue such as rappelling, belaying and lowering. Manufactured of forged alloy aluminum and hard coat anodized for extended wear.

• Strength 8000 lbf. (35kN)

(B) 6008 RSI Large Figure 8
Forged steel. Plated for longer wear and corrosion resistance. Steel figure eights are ideal for high cycle because of their resistance to grooving and excessive wear. Three dimensional design is asymmetrical and allows user to vary the friction. Steel figure eights do not provide as much friction as aluminum figure eights and care must be taken with their use.

• Strength 45,000 lbf. (200kN)

7020 Petzl I'D
Self braking device designed for lowering systems, descending rope and for belaying. Anti-panic feature built in. Easily releaseable after locking. Climbing is also possible with the addition of a rope grab and a foot stirrup or etrier. Works great in mechanical advantage haul systems and as a lowering/progress capture device in ganged-on haul systems. UL classified to meet NFPA 1983/2006 edition standards.

7009 Petzl Stop
Self braking descent device that stops when the handle is released. Speed of descent is controlled by varying the grip on the free end of the rope. Can be installed on the rope without disconnecting it from the harness. Climbing is also possible with the addition of a rope grab and a foot stirrup or etrier. Can also be used effectively in haul systems. Great for rope access work.

SMC Brake Racks
One of the most widely used descent and lowering devices available. It will accept single or double ropes of several diameters and yet provides a wide range of friction for descent control or lowering control. Allows the user to change the number of bars as necessary when in use with a load. UL classified to meet NFPA 1983/2006 edition standards.

• 1 inch diameter stainless steel tie off bar
• 7/8 inch diameter blue anodized aluminum bar with training groove and straight slot

1401

Straight

1402

Twisted (shown)

1404 SMC 4 Bar U-Rack
This compact rack is fitted with 4 long-wear tubular stainless bars, two of which are tie-off bars. This rack design allows the user to vary the friction without adding or dropping bars or disconnecting from the system like traditional racks, whether it is being used in a controlled, fast single person rappel or a heavy rescue lower. As more professional trainers begin to expose their clients to the benefits of this alternative style rack, it is clear they are growing in acceptance and popularity. UL classified to meet NFPA 1983/2006 edition standards.

Mallions
Steel screw links used as an alternative to standard carabiners. Excellent where semi-permanent attachments are made. Great multi-directional loading capacity.

1779

Stainless

WLL 625 Kg

1780

Plated Steel

1781

9mm

Stainless

WLL 700 Kg

1783

Oval

1011 ISC Rescue Ascenders
Heavyweight construction specifically designed for rigging and rescue applications. These are no lightweight rock climbing ascenders! Easy to operate with gloved hand, these ascenders come with large thumb release on cam, molded hand grip and double clip-in points. 9 to 13 mm ropes. Strength (frame) 6000 lbf. (26.6kN).

(A) 7016 Petzl Croll
Attaches to front of harness in chest area to help user maintain an upright position. Basic Rope Access harness and RTR Tower Harness have attachment points built-in .
(B) 7050 Petzl Rescucender
Rope grab suitable for hauling heavy loads. Incorporated into a hauling system, it operates as a progress capture device. Acts as a load limiter if overloaded or subjected to an impact force. Available in all black.

7036 SMC Swivel
Keep ropes from becoming twisted or wrapped. Oval hole to accommodate 2 carabiners. Sealed bearing. Strength 9000 lbf. (36kN). UL classified to meet NFPA 1983/2006 edition standards.

7035 Petzl Swivel L
Keep ropes from becoming twisted or wrapped. Sealed bearing. Strength 9000 lbf. (40kN). UL classified to meet NFPA 1983/2006 edition standards and CE.

1010 Wall Rigger
Small rigging plate ideal for SAR, tactical and stage rigging applications. Made of 3/16 inch 7075-T6 aircraft aluminum. Length 3.3 inches, width 3.6 inches. Hole size .75 inch (19mm). Strength 6750 lbs (30kN).

1010R

Red

1010B

Black

1012 Mini Rigger
Small rigging plate ideal for all technical rescue rigging applications. Made of 3/8 inch high strength 6061-T6 aircraft aluminum. Length 4 inches, width 4.4 inches. Hole size .75 inch (19mm). Strength 10,000 lbf. (44kN). UL classified to meet NFPA 1983/2006 edition standards.

1012

Orange

1012B

Black

1015 Rescue Rigger
Medium rigging plate ideal for all technical rescue rigging applications. Made of 3/8 inch high strength 6061-T6 aircraft aluminum. Length 6.5 inches, width 4.25 inches. Hole size.75 inch (19mm). Strength 10,000 lbf. (44kN). UL classified to meet NFPA 1983/2006 edition standards.

1015

Red

1015B

Black

Double Locking Ladder Hook

• 2.5 inch (63.5mm) gate opening
• Strength 5000 lbf. (22.2kN)
• Also available in steel 1.75 inch gate opening

838S

Steel

838A

Aluminum

837

Small Steel 1.75 opening

Double Locking Snap Hook

• .75 inch (19mm) gate opening
• Strength 5000 lbf. (22.2kN)

839S

Steel

839A

Aluminum

1337 Steel Captive Eye 3 Stage
Designed for arborist and rigging use.

• .75 inch (19mm) gate opening
• Strength 10,125 Ibf. (45kN)

1775 Kong Tango
Autolock snap hook, personal use carabiner for search, escape and personal edge protection kits.

• 1.05 inch (26.6mm) gate opening
• Strength 7425 lbf. (33kN)