Filter Result By

Browse

Manufacturers

Bluewater Roof Hatch Floor Door & Skylight Guardrail Systems

Bluewater Roof Hatch Floor Door & Skylight Guardrail Systems

Manufacturer: Bluewater

Product Code: RoofHatchSkyLightGR

Bluewater Roof Hatch Floor Door & Skylight Guardrail Systems


Protect your employees, and your investment while complying with OSHA regulations. It’s that simple.


OSHA requires guardrail protection on the exposed sides of openings of roofs and floors in most situations. Bluewater Manufacturing’s SafetyRail 2000 Guardrail System is designed to meet this safety concern. In fact, our roof Hatch/Skylight Systems exceed OSHA Std. 29 CFR 1910.23. The Roof Hatch/Skylight System is installed in minutes and easily dismantled for roof repair.


Safety and Ease

For roof hatch, skylight, fire vent and floor door protection

  • Non—penetrating
  • Independently tested to comply with OSHA fall protection regulations for guardrails
  • Installs in minutes
  • Easily dismantled for roof repair
  • Designed to erect in numerous configurations (L-shapes, straight runs, and more)
  • 1-5/8” diameter rails come with a quality Powder Coat finish or Hot Dipped Galvanized finish

 

OSHA Compliance

Compliant with regulations for guardrails:
29 CFR 1910.23
29 CFR 1926.502

Note: A setup using a chain does not meet OSHA regulations. The chain does not provide a mid-rail as required.

 

Product Specifications

 

Roof & Floor Opening Protection: Provides freestanding pedestrian egress barrier system on roof, including pipe railings, uprights, bases and fittings
Approved products Roof Hatch Floor Door and Skylight Guardrail Systems
Standards: System Shall have top and mid rail in accordance with OSHA Standards - 29 CFR 1910.23 and CFR 1926.502
Structural Load: 200 lb (90.7 kg), minimum, in any direction to all components in accordance with OSHA Regulations 29 CFR 1910.23 and CFR 1926.502
Height: 42 inches (1067 mm), minimum
Railings: 1-5/8inch (41 mm) O.D. hot rolled picked electric weld tubing, free of sharp edges and snag points
Mounting Bases: Class 30 gray iron material cast with four receiver posts. Base weight 108 lbs and 48 lbs per square foot. Rubber pads on base bottoms.
Receiver Posts: Shall have a positive locking system into slots that allow rails to be mounted in any direction. Friction locking systems are not allowed. Receiver posts shall have drain holes.
Hardware: Securing pins shall be 1010 carbon steel, zinc plated and yellow chromate dipped. Pins shall consist of collared pin and lanyard that connects to lynch pin.
Finishes: Available in standard Powder Coat Yellow and Hot-Dip Galvanized. Custom colors available.

 

Options
Toe Board Brackets: Provide brackets as manufactured by BlueWater Mfg. Inc
Surface Protection Pads: EDPM Rubber Pads and Bur Pads are available

 

Independent Test Results

Test Conclusions:

  • The portable guardrail system was found to comply with OSHA regulation 1926.502 for Fall Protection.
  • The top rail was capable of withstanding a 200 pound horizontal and vertical load.
  • The midpoint of the top rail deflected to 40.75 inches above the floor level when subjected to a 200 pound vertical load.
  • The mid rail was capable of withstanding, without failure, a force of 150 pounds, applied in the vertical and horizontal directions.

Tests were conducted by GME Consultants, Consulting Engineers, Minneapolis, MN 55447. Complete Report available from BlueWater.

Wind Load Calculations

Available on request.

Related Categories


Request a Quote Now

Request a Quote X

Your Name*
Please let us know your name.

Company Name
Invalid Input

Your Email*
Please let us know your email address.

Phone*
Invalid Input

Category*
Please enter valid Product/Category

Product Url
Enter valid Product Url

Comment
Please let us know your message.

Captcha*
Captcha   RefreshPlease enter the right CAPTCHA

Processing...