Spill Prevention, Control and Countermeasures Rule

A. BACKGROUND:

• Under authority of The Federal Water Pollution Control Act (as amended by The Clean Water Act) the SPCC rule took effect on January 10, 1974. Its purpose is to prevent oil and oil-related materials from reaching navigable waters and adjoining shorelines. Parts of the original rule were unclear (i.e., container size was not specified) and compliance was expensive for small business due to the need to obtain certification by a Professional Engineer (PE). As a result, the original rule was revised in July 2002. Various extensions have taken place since then that address special cases. (See section F below).

B. SUMMARY:

• Facilities subject to the rule must prepare and implement a plan to prevent any discharge of "oil" into or upon navigable waters of the u.s. (including groundwater that leads to surface water) or adjoining shorelines. This written plan is called an SPCC Plan.
• Unlike oil spill contingency plans that address spill cleanup measures after a spill has occurred, SPCC Plans ensure that facilities put in place containment and other countermeasures that would prevent oil spills that could reach navigable waters.
• The SPCC Plan must address: (a) operating procedures the facility implements to prevent oil spills; (b) control measures installed to prevent oil from entering navigable waters (i.e. secondary containment); (c) countermeasures to contain, clean up and mitigate the effects of oil spills.

C. REGULATED MATERIALS:

• Animal oils, fats and greases (including oils from fish or marine mammals), asphalt, aviation gasoline, bunker fuel, crude oil, cutting oil/machine coolants, dielectric fluid, diesel fuel, heating oil, gasoline, greases, hydraulic oil, jet fuel, lubricating oil, mineral spirits, motor oil, naptha, natural gas condensate, oil refuse, oily wastes (other than oil mixed with dredged soil), stoddard solvent, synthetic oils, tall oil, turpentine, residual fuels, used oil, vegetable oils (including oils from nuts, seeds, fruits and kernels).

D. WHAT FACILITIES ARE REGULATED?

• Facilities with combined (indoor and outdoor), above-ground oil storage capacity (not actual gallons on site) dedicated to any of the regulated materials greater than 1,320 gallons or a completely buried storage capacity greater than 42,000 gallons must comply.
• To calculate oil storage "capacity", all containers with a capacity of 55 gallons or more are included.
• Overall, the Rule applies to owners or operators of facilities that drill, produce, gather, store, use, process, refine, transfer, distribute or consume oil or oil products.

E. WHAT ACTIONS ARE NECESSARY FOR COMPLIANCE?

• All qualifying drums and tanks must have secondary containment and be included in the written Plan.

Facilities with above-ground oil storage capacity of 10,000 gallons or less are permitted to self-certify their Plan (no PE required) if they meet certain criteria related to spill history. Secondary containment is also required for loading and unloading areas for tanker trucks and railcars. Secondary containment must be equal to the largest vessel. In the case of a railcar, the containment area must provide a means to divert a significant spill to a retention pond, oil/water separator, etc.

• The Plan must include a facility diagram, and must mark the location and contents of each container. Secondary containment must be constructed so that any discharge from a primary containment system (i.e. drum, tank or pipe) will not escape before cleanup occurs.
  
  F. EPA HAS ISSUED COMPLIANCE DATE EXTENSIONS - WHAT DOES THAT MEAN?

• EPA has caused a great deal of confusion related to its various extensions. Soon after the 2002 rule changes were published, concerns expressed by industry focused on four (4) problem areas:

• Qualified, oil-filled operational equipment
• Motive power containers (e.g. vehicle fuel tanks)
• Mobile refuelers
• Animal fats & vegetable oils at onshore & offshore oil production, drilling facilities

The most recent extension date (currently July 1, 2009) applies only to the four (4) special cases listed above. The July 1, 2009 date is not an extension date for general compliance with SPCC.

G. WHO MUST COMPLY AND WHEN?

• Compliance dates for facilities (other than farms) are as follows:
  
  A facility starting operation on or before August 16, 2002 MUST
  Maintain its existing Plan; must amend and implement the Plan no later than July 1, 2009. Facilities in this group that do not currently have an SPCC Plan are out of compliance and are subject to regulatory action.
  A facility starting operation after August 16, 2002 through July 1, 2009 MUST
  Prepare and implement a Plan no later than July 1, 2009.
  A facility starting operation after July 1, 2009 MUST
  Prepare and implement a Plan before beginning operations.

H. OTHER SPCC-RELATED ITEMS

• An SPCC inspector is not required to provide advance notice of a facility inspection.
• Facility owners or operators regulated by SPCC must designate a person who is accountable for discharge prevention and who reports directly to management.
• In general, "transfers" of oils are regulated by SPCC; "transportation" of oil is not regulated.

ULTRA-275 CONTAINMENT SUMP

• Eliminate costly spills while storing fuels, oils and other hazardous liquids.
• Rugged, all polyethylene construction will not rust or corrode.
• Optional 3/4" drain fitting alliows use with Ultra-Self Bailer (see below).
• Meets EPA Container Storage Regulation 40 CFR 264.175.
• Helps comply with SPCC and NPDES,40 CFR 122.26 (1999).

ULTRA-550 CONTAINMENT SUMP

• Economical containment for 500 and 550 gallon fuel and oil tanks.
• 100% polyethylene construction will not rust or corrode; provides superior chemical and weather resistance.
• Optional 3/4" drain fitting available.
• Use with optional Ultra-Self Bailer (Part# 9935) for outdoor containment - Self Bailer allows clean stormwater to passively drain from sump while capturing hydrocarbons.
• Meets Stormwater, SPCC and EPA Containment Regulations.

ULTRA-1000 CONTAINMENT SUMP

• Contains 1000-gallon fuel tanks.
• 1-piece molded polyethylene design - will not rust or corrode.
• Nestable design saves freight and minimizes storage space.
• Optional 3/4" drain fitting available - allows use with Ultra-SelfBailer.
• 2" drain fitting also available.
• Use with optional Ultra-Self Bailer (Part# 9935) for outdoor containment - Self Bailer allows clean stormwater to passively drain from sump while capturing hydrocarbons.
• Meets Stormwater, SPCC and EPA Containment Regulations.

ULTRA-275 CONTAINMENT SUMP

ULTRA-550 CONTAINMENT SUMP

ULTRA-lOOO CONTAINMENT SUMP

Part# 2800: no drain • Part# 2801: with drain

Part# 2823: no drain • Part# 2820: with drain

Part# 2830: no drain • Part# 2831: with 3/4" drain • Part# 2832: with 2" drain

Outside Dimensions: 84 1/2" x 43 3/4" x 29"

Outside Dimensions: 87" x 62 1/4" x 32 3/4"

Outside Dimensions: 148" x 63" x 33"

(2147 mm x 1112 mm x 737 mm)

(2210 mm x 1582 mm x 832 mm)

(3759 mm x 1600 mm x 838 mm)

Inside Top: 80" x 39"; Inside Bottom 73" x 31"

Inside Bottom: 75 3/4" x 47 3/4"

Inside Bottom: 144" x 56"

(2032 mm x 991 mm); (1855 mm x 788 mm)

(1925 mm x 1213 mm)

(3315 mm x 1156 mm)

Weight: 90 lbs. (41 kg)

Weight: 108 lbs. (49 kg)

Weight: 180 lbs. (82 kg)

Containment Capacity: 360 gallons (1363 L)

Containment Capacity: 605 gallons (2291 L)

Containment Capacity: 1,100 gallons (4164 L)

Optional PullOver Cover, Part# 2810; Ultra-SelfBailer

Option: Ultra-SelfBailer

Option: Ultra-SelfBailer

Drum Handling, Dispensing and Containment in One Unit

• Rugged polyethylene construction offers excellent chemical resistance.
• Unlike alternative products, the open containment sump does not require spills to flow inside the double walls to meet EPA regulations - easy to clean; eliminates residue concerns as related to compatibility.
• Can be used with 55- or 30-gallon drums - nylon strap keeps drums secure.
• Ergonomically designed for safe and easy handling.
• large 10" wheels roll easily over shop and factory floors.
• Part# 1312 has large, pneumatic wheels for soft or uneven surfaces.
• large containment sump (66 gallons) meets SPCC and EPA Containment Regulations.

Nearly 50% lower than standard spill pallets, drum handling is safer and less strenuous.

• Available in 1-drum, 2-d rum and 4-drum configurations.
• Removable grates feature a non-slip surface.
• Superior weight capacity of the 4-drum model also allows use with IBC tanks.
• All models meet SPCC and EPA Container Storage Regulation 40 CFR 264.175 for use with drums.

Part# 9606: no drain

Part# 9607: with drain

Part# 9610: no drain

Part# 9611: with drain

Part# 9630: no drain

9631: with drain

Dimensions: 40" x 40" x 12"

Weight: 51 lbs.

Dimensions: 65 1/2" x 40" x 8 3/4"

Weight: 88 lbs.

Dimensions: 62" x 62" x 8 3/4"

Weight: 125 lbs.

Uniformly Distributed Load:

Containment Capacity:

Uniformly Distributed Load:

Containment Capacity:

Uniformly Distributed Load:

Containment Capacity:

8001bs.

62 gallons

4,500 lbs.

66 gallons

9,000 lbs.

75 gallons

Options Available: Polyethylene Loading Ramp, PullOver Covers

Hidden Containment Bladder Automatically Unfurls To Capture large Spills Or Drum leaks
Ultra-SpillDeck Bladder Systems are low profile, polyethylene containment decks which meet EPA and Uniform Fire Code Spill Containment Regulations. Available in 1, 2 and 4-drum modules, the low 5-3/4" deck height allows safe and convenient drum loading, even without drum handling equipment. Add the optional polyethylene loading ramp for even greater handling ease.

Ultra-Spill Deck P1 Bladder System

• Compact 25 7/8" x 30 1/2" footprint saves valuable floor space - perfect for single-drum waste collection usage.
• The first and only low profile, single-drum containment unit which meets SPCC, EPA Container Storage Regulation 40 CFR 264.175 and Uniform Fire Code Spill Containment Regulations.

Part# 2317
Polyethylene bladder is housed inside the Bladder Attachment. Connect the Bladder Attachment to the SpillDeck in seconds - no tools required!

Ultra-Spill Deck P2 Bladder System

• Store 2 drums on the all-polyethylene, space-saving 25 7/8" x 52" SpillDeck P2 Bladder System.
• Low 5 3/4" deck height is the same as wooden pallets - allows drums to be "jockeyed" onto Spill Deck Systems when standard drum handling equipment is not available.
• Applications include satellite waste collection, drum pump stations and storage of virgin chemicals.
• Meet SPCC, EPA Container Storage Regulation 40 CFR 264.175 and Uniform Fire Code Spill Containment Regulations.

Ultra-SpillDeck P4 Bladder System

• Use the 4-drum Spill Deck Bladder System in place of taller containment pallets -low 5 3/4" deck height offers significant safety and handling benefits.
• Overspills and small leaks are captured in the 44-gallon sump; catastrophic leaks deploy the bladder, allowing the 4-drum system to meet regulations.
• Applications include satellite waste collection, drum dispensing, storage of virgin chemicals and hazardous wastes.
• Meet SPCC, EPA Container Storage Regulation 40 CFR 264.175 and Uniform Fire Code Spill Containment Regulations.
• Use optional bulkhead fittings to connect 1, 2 or 4-drum Spill Deck modules together. A virtually unlimited number of custom configurations can be designed to meet your specific needs.
• Spill Deck configurations which accommodate 6 or more 55-gallon drums do not require usage of the Bladder Attachment to meet SPCC, EPA and Uniform Fire Code Regulations. Any 6-drum configuration, when connected with optional bulkhead fittings, will have a 66-gallon sump capacity without a Bladder Attachment.
• Spill Deck Bladder Systems require adequate aisle space to allow the Bladder to unfurl properly.

ULTRA-SPILLDECK BLADDER SYSTEMS

Ultra-Spill Deck P1 Bladder System

Ultra-Spill Deck P2 Bladder System

Part# 1320

 Part# 2329

Dimensions:
25 7/8" x 30 1/2" X 5 3/4"

Dimensions:
52" X 30 1/2" x 5 3/4"

Weight: 27 lbs.

Weight: 44 lbs.

Uniformly Distributed Load: 1,500 lbs.

Uniformly Distributed Load: 3,000 lbs.

Containment Capacity: 66 gallons

Containment Capacity: 77 gallons

Sump Capacity prior to spill entering bladder: 11 gallons

Sump Capacity prior to spill entering bladder: 22 gallons

Bladder Attachment

Bladder Pump

Part# 2317
(Includes bladder, bulkhead fitting)

Part# 6340
(Includes bulkhead fitting)

Part# 2345

Dimensions:
25 1/8" x 4 5/8" X 45/8"

Weight: 4 lbs.

Weight: 3 lbs.

SpiliDeck Pl Module, Spill Deck P2 Module, SpillDeck P4 Module, Bulkhead Fitting, 26" T-Strip.

Low Profile, "In Line" Designs Save Valuable Floor Space And Comply With Spill Containment Regulations

• Standard Inline Models include 3-drum, 4-drum, 5-drum and 6-drum configurations.
• Narrow 25 7/8" depth allows drums to be stored in a single row along facility walls ­minimizes space requirements.
• Low profile design reduces safety and handling concerns found with taller containment pallets.
• Additional Spill Deck modules can be easily connected to an existing Inline configuration - allows more drums to be added to your containment area as storage needs grow.
• All models meet SPCC, EPA Container Storage Regulation 40 CFR 264.175 and Uniform Fire Code Spill Containment Regulations.

3-, 4- and 5-Drum Units utilize a hidden containment bladder for additional sump capacity to meet EPA and UFC Spill Containment Regulations.

Ultra-lnLine Spill Deck 3-Drum Model

Ultra-lnLine Spill Deck 4-Drum Model

Ultra-lnLine Spill Deck 5-Drum Model

Ultra-lnLine Spill Deck 6-Drum Model

Part# 2360

Part# 2361

Part# 2333

Part# 2334

Dimensions:
77-7/8" x 25-7/8" x 5-3/4"

Dimensions:
104" x 25-7/8" x 5-3/4"

Dimensions:
129-7/8" x 25-7/8" x 5-3/4"

Dimensions:
156" x 25-7/8" x 5-3/4"

Weight: 67 lbs.

Weight: 84 lbs.

Weight: 107 lbs.

Weight: 132 lbs.

Uniformly Distributed Load: 4,500 lbs.

Uniformly Distributed Load: 6,000 lbs.

Uniformly Distributed Load: 7,500 lbs.

Uniformly Distributed Load: 9,000 lbs.

Containment Capacity: 88 gallons

Containment Capacity: 99 gallons

Containment Capacity: 110 gallons

Containment Capacity: 66 gallons

Option: Loading Ramp Part#1089, Dimensions 24" x 32" x 5 3/4", Weight 17 lbs.

Low Profile, Modular SpillDecks Allow You To Design And Create A Containment System That Meets Your Specific Needs
Ultra-SpiliDecks are available in 1, 2 and 4-drum modules. Modules are easily connected together with bulkhead fittings to allow a virtually unlimited number of customized configurations.

• Polyethylene construction meets a wide range of chemical compatibility needs.
• Low profile, 5 3/4" height offers safe and convenient loading/unloading of drums.
• Applications include hazardous waste collection, storage of virgin chemicals, drum dispensing and battery storage.
• Optional Loading Ramps provide added drum handling safety and convenience.
• Meet SPCC, EPA Container Storage Regulation 40 CFR 264.175 and Uniform Fire Code Spill Containment Regulations.

The bulkhead fittings not only "lock" connected modules together, but allow spilled liquid to flow from one module to the next. Ultra-SpillDeck Containment Systems meet SPCC, EPA and Uniform Fire Code Spill Containment Regulations when assembled in configurations of six (6) drums or more.

Connect your choice of 1,2 and 4-drum SpillDeck modules to custom­design your own secondary containment storage pad.

Ultra-SpillDeck Pl Module

Ultra-SpillDeck P2 Module

Ultra-Spill Deck P4 Module

Ultra-Spill Deck loading Ramp

Part# 1321

Part# 1086

Part# 1072

Part# 1089

Dimensions: 25 7/8" x 25 7/8" x 5 3/4"

Dimensions: 52" x 25 7/8" x 5 3/4"

Dimensions: 52" x 52" x 5 3/4"

Dimensions: 24" x 32" x 5 3/4"

Weight: 23 lbs.

Weight: 40 lbs.

Weight: 62 lbs.

Weight: 17 lbs.

Uniformly Distributed load: 1,500 lbs.

Uniformly Distributed Load: 3,000 Lbs.

Uniformly Distributed Load: 6,000 Lbs.

Options: 26" T-Strip, 2 required/long side Bulkhead Fitting Sidewall Plug

Containment Capacity: 11 gallons

Containment Capacity: 22 gallons

Containment Capacity: 44 gallons

Available in 6-drum and 8-drum models, Ultra-SpillDecks are perfect for satellite collection of hazardous wastes or storage of virgin chemicals.

• One-piece, molded sump with elevated 2' x 4' black grates.
• Polyethylene grates feature slip resistant, "diamond plate" surface design.
• Deck holds up to 1,500 lbs. per drum UDL (uniformly distributed load).
• Designed for use with Ultra-Spill Deck Loading Ramp (Part# 1089).
• Meet SPCC, EPA and Uniform Fire Code Spill Containment Regulations.

ULTRA-SPILLDECKS

Ultra·SpillDeck P6

Ultra·SpillDeck P8

Part# 1175

Part# 1075

Dimensions: 74 1/4" x 50" x 5 1/4"

Dimensions: 98 1/2" x 50" x 5 1/4"

Weight: 86 Ibs.

Weight: 110 Ibs.

Uniformly Distributed Load: 9,000 Ibs.

Uniformly Distributed Load: 12,000 Ibs.

Containment Capacity: 66 gallons

Containment Capacity: 75 gallons

The Only l-Drum, Lockable Outdoor Containment Unit Available

• Convenient "roll-top" cover slides up and out of the way - allows quick access to drum pumps and funnels.
• 100% polyethylene construction will not rust or corrode.
• Safe Handling - can be moved by forklift under the "shoulder" area or wheeled with the optional dolly.
• Meets SPCC and EPA Container Storage Regulation 40 CFR 264.175.
• Helps meet new Stormwater Management Regulations - NPDES, 40 CFR 122.26 (1999).

Ultra-HardTop Pl Plus

Dolly

Part# 9640: no drain
Part# 9641: with drain

Part# 0417

Dimensions: 36" x 36" x 66"

Dimensions: 26 1/2" x 26 1/2" x 5"

Weight: Top 36 Ibs. Weight: Bottom 26 Ibs.

Weight: 31 lbs.

Load Capacity: 800 lbs.

Load Capacity: 800 lbs.

Containment Capacity: 64 gallons

Construction: Steel

Ultra-HardTop P2 Plus is lockable with a standard padlock, and can be safely lifted by forklift with drums in place.

• Tall 23 3/4" head space easily accommodates rotary drum pumps and large conical funnels.
• Low profile (8 3/4") containment pallet positions drum-top funnels at a safe, convenient level to pour hazardous wastes.
• 100% polyethylene construction will not rust or corrode.
• Meets SPCC, EPA Container Storage Regulation 40 CFR 264.175 and Uniform Fire Code Spill Containment·Regulations.
• Helps meet new Stormwater Management Regulations ­ NPDES, 40 CFR 122.26 (1999).

Ultra-HardTop P2 Plus

Loading Ramp

Part# 9612: no drain  Part# 9613: with drain

Part# 0676

Dimensions: 67 1/4" x 41 1/4" x 74"

Dimensions: 46" x 28" x 8 3/4"

Weight: 260 Ibs.

Weight: 25 lbs.

Uniformly Distributed Load: 4,500 lbs.

Surface: Non-slip

Containment Capacity: 66 gallons

Construction: Polyethylene

Safely Store 4 Drums Outdoors

• Unique "dual closure" offers significant ergonomic and convenience benefits - drums are easily accessed from either side.
• Roll-top covers can be easily lifted from waist height to access drum tops - no need to reach near ground level.
• low profile (8 3/4") containment pallet positions drum­tops at a safe, convenient level to pour wastes into funnels or to use drum pumps.
• Forkliftable, lockable, all-polyethylene construction will not rust or corrode.
• Helps meet new Stormwater Management Regulations ­NPDES, 40 CFR 122.26 (1999).
• Meets SPCC and EPA Container Storage Regulation 40 CFR 264.175.

Part# 9636: no drain

Weight: 440 Ibs.

Part# 9637: with drain

Containment Capacity: 75 gallons

Outside Dimensions: 64 1/2" x 62" x 79"

Uniformly Distributed Load: 9,000Ibs.

Options: Loading Ramp (part# 0676) - stores inside containment unit when not in use

Safely Store Multiple Drums Outdoors

• Available in 8, 12, 16 and 20-drum models. Extender Kits are available to expand capacity beyond 20-drums.
• All polyethylene construction ­offers excellent chemical resistance, will not rust or corrode.
• Separate, lockable compartments feature a unique I/2-way" entry system - allows quick access to all four (4) drums.
• Roll-top covers can be easily lifted from waist height to access drum tops.
• Swing-out doors provide safety and convenience for loading or unloading drums.
• Low-profile (8-3/4" height) containment pallet positions drum-tops at a safe, convenient level to pour wastes into funnels or to use drum pumps.
• Rugged, 9,000 lb. uniformly distributed load (UDL) capacity per compartment allows safe storage of IBC tanks as well as drums. See pages 22-23.
• Units ship partially unassembled for freight savings.
• Meets EPA Container Storage Regulation 40 CFR 264.175 and helps comply with NPDES, 40 CFR 122.26 (1999). Considered a Stormwater Management "Best Management Practice" product (BMP). Also meets SPCC Regulations.

Multiple I/4-drum compartments" offer flexible usage for a broad range of operations including: storage of virgin chemicals, active hazardous waste
collection and storage of spill response supplies. Internal walls and separate sumps allow materials to be segregated.

Part# 9650: HardTop P8, no drain, 815 lbs.
Part# 9651: HardTop P8, with drain, 815 lbs.
Dimensions: 126" x 62" x 79"
Capacity: (8) 55-gallon drums

Part# 9652: HardTop P12, no drain, 1190 lbs.
Part# 9653: HardTop P12, with drain, 1190 lbs.
Dimensions: 188" x 62" x 79"
Capacity: (12) 55-gallon drums

Part# 9654: HardTop P16, no drain, 1565 lbs.
Part# 9655: HardTop P16, with drain, 1565 lbs.
Dimensions: 250" x 62" x 79"
Capacity: (16) 55-gallon drums

Part# 9656: HardTop P20, no drain, 1940 lbs.
Part# 9657: HardTop P20, with drain, 1940 lbs.
Dimensions: 312" x 62" x 79"
Capacity: (20) 55-gallon drums

Part# 9658: 4-Drum HardTop Extender Kit, no drain, 375 lbs
Part# 9659: 4-Drum HardTop Extender Kit, with drain, 375 lbs.

Weight Capacity: 9,000 lbs. UDL per compartment
Containment Capacity: 75 gallons per compartment

Options: Polyethylene Loading Ramp - Part# 0676

Four inner polyethylene columns support uniformly distributed loads of up to 8,500 lbs. All components are easily removed for cleaning.

Economical And Portable Containment For IBCs

• Low profile, 28" overall height - allows safe and convenient IRC tank handling and dispensing.
• All polyethylene construction - offers excellent cllemical resistance and will not rust or corrode.
• Forkliftable - allows convenient positioning to desired locations.
• Low-cost design with value-added features and benefits.
• Large 52" x 52" deck allows safe and convenient placement of IRC tanks.
• Small footprint - 62" x 62" unit requires minimal floor space.
• Available with optional Bucket Shelf (Part# 1160) - catches leaks or spills during dispensing.
• 360-gallon sump capacity meets SPCC and EPA Container Storage Regulations.

Ultra-IBC Spill Pallet Plus

Ultra-BucketShelf

Part# 1157: no drain
Part# 1158: with drain

Containment Capacity: 360 gallons

Part# 1160

Dimensions: 62" x 62" x 28"

Uniformly Distributed Load: 8,500 lbs.

Weight: 324 lbs.

Meets EPA Container Storage Regulation 40 CFR 264.175,

Weight: 10 lbs.

Save Money - Store Two IBC Tanks Side-By-Side

• Use for intermediate bulk containers (IBCs), drums, or other large vessels. (All materials stored must be chemically compatible.)
• One-piece, molded sump holds 535 gallons - meets EPA Containment and SPCC Regulations for two IBC tanks.
• Available with optional Bucket Shelf for either or both sides - catches small leaks or spills during dispensing.
• Grates are easily removed for quick clean-up.

Part# 1140: no drain
Part# 1144: with drain

Part# 1141: no drain, w/l Right Side Bucket Shelf

Part# 1142: no drain, w/l Left Side Bucket Shelf

Part# 1143: no drain, w/2 Bucket Shelves

Part# 1145: with drain, w/l Right Side Bucket Shelf

Part# 1146: with drain, w/l Left Side Bucket Shelf

Part# 1147: with drain, w/2 Bucket Shelves

Dimensions: Twin IBC SpillPallet - 124-1/2" x 61 5/8" x 22" Bucket Shelf: 19 1/2" 16" x 14 1/2"

Part# 1160: Bucket Shelf

Weight: Twin IBC Spill Pallet - 452 lbs.
Bucket Shelf: 10 lbs.

Weight Capacity: 8,000 Ibs. UDL/side
Gallon Capacity: 535 gallons

Comply With Regulations While Storing IBC Tanks Outdoors

• Upper roll-top door and lower swing-out doors combine to allow easy and convenient access to 1Be.
• Safely stores an IBC tank with maximum dimensions of 52" x 52" x 61".
• low profile (28" height), 360 gallon containment sump allows safe material handling and dispensing.
• Forkliftable, lockable, all-polyethylene design will not rust or corrode.
• Helps meet new Stormwater Management Regulations ­NPDES, 40 CFR 122.26 (1999).
• Meets SPCC and EPA Container Storage Regulation 40 CFR 264.175.

Part# 1162: no drain

Weight: 525 lbs.

Part# 1161: with drain

Containment Capacity: 360 gallons

Outside Dimensions: 64 1/2" x 62" x 96"

Uniformly Distributed Load: 8,500 lbs.

Outdoor Storage for Two IBC Tanks

• Uses same sump as Ultra-Twin IBC SpillPallet (see above).
• Unique, lockable, dual closure allows quick access to tanks.
• Roll-top covers can be easily lifted for routine visual inspection.
• Swing-out doors provide safety and convenience for loading / unloading tanks.
• Safely stores IBC tanks, with maximum dimensions of 52" x 52" x 61".
• Meets Stormwater, SPCC and EPA Containment Regulations.

Part# 1148: no drain
Part# 1149: with drain

Weight: 1167 lbs.

Sump Capacity: 535 gallons
Weight Capacity: 8,000 lbs. UDL/side

Dimensions: 128" x 67" x 96"

Option: Bucket Shelf, Part# 1160

Low-Cost Spill Containment for Multiple IBC Tanks

• Indoor and Outdoor Models available for 2, 3, 4 or 5 tanks.
• Each IBC tank sits on a low-profile spill pallet with a containment capacity of 75 gallons - Expansion Tanks provide 65 gallons of additional capacity.
• 100% polyethylene construction ­eliminates the potential for rust and corrosion.
• "Flow-through" bulkhead fittings connect spill pallets and Expansion Tanks together, allowing spills to be channeled throughout the containment system - containment capacity is thereby "borrowed" from adjacent spill pallets and Expansion Tanks.
• Meets SPCC and EPA Container Storage Regulation 40 CFR 264.175.
• Outdoor models help meet new Stormwater Management Regulations ­NPDES, 40 CFR 122.26 (1999).
• Meets SPCC and EPA Container Storage Regulation 40 CFR 264.175.
• Outdoor models help meet new Stormwater Management Regulations ­NPDES, 40 CFR 122.26 (1999).

OUTDOOR MODEL FEATURES:

• Unique "roll top" enclosures and swing-out doors allow convenient loading and unloading of !BC tanks.
• Compartments are lockable for secure storage of hazardous materials.
• Optional Extender Kits (Part# 9658) provide for the addition of another compartment. (Holds 1 IBC tank per Extender Kit).

ULTRA-MODULAR IBC SPILLPALLETS

Components Included (Qty)

Part#

Description

Dimensions

Weight Capacity

Gallon Capacity

Weight

Pallets

Exp. Tanks

I
n
d
o
o
r

1125

2- Tank Model

186" x 62" x 8 3/4"

9,000 Ibs. UDL per Pallet

280 gal.

310 lbs.

(2)

(2)

1126

3-Tank Model

248" x 62" x 8 3/4"

9,000 Ibs. UDL per Pallet

355 gal.

435 lbs.

(3)

(2)

1127

4-Tank Model

279" x 62" x 8 3/4"

9,000 Ibs. UDL per Pallet

365 gal.

531 lbs.

(4)

(1)

1128

5-Tank Model

310" x 62" x 8 3/4"

9,000 Ibs. UDL per Pallet

375 gal.

625 lbs.

(5)

(0)

1118

Assembly Kit

Includes hole saw, arbor and set of 2 tightening tools REQUIRED

9630

SpillPaliet Only

62" x 62" x 8 3/4"

9,000 Ibs. UDL

75 gal.

125 lbs.

NA

NA

O
u
t
d
o
o
r

1165

2-Tank Model

126" x 93" x 79"

9,000 Ibs. UDL per Pallet

280 gal.

881 lbs.

(2)

(2)

1166

3-Tank Model

188" x 93" x 79"

9,000 Ibs. UDL per Pallet

355 gal.

1258 lbs.

(3)

(2)

1167

4- Tank Model

250" x 93" x 79"

9,000 Ibs. UDL per Pallet

365 gal.

1603 lbs.

(4)

(1)

1168

5- Tank Model

312" x 62" x 79"

9,000 Ibs. UDL per Pallet

375 gal.

1948 lbs.

(5)

(0)

1118

Assembly Kit

Includes hole saw, arbor and set of 2 tightening tools REQUIRED

9658

Extender Kit

64" x 62" x 79"

9,000 lbs. UDL

75 gal.

375 kbs.

NA

Options/Accessories: Part# 1117 - 2" Bulkhead Fittings (Set of 2),
Part# 1124 - Expansion Tank only, 61" x 31" x 12 1/2", Capacity: 65 gallons, 30 lbs.

Capture Hazardous Spills from Railroad Tanker Cars and Locomotives
Ultra-TrackPans have been designed to provide spill containment at industrial rail sidings, locomotive maintenance and fueling facilities. Available in virtually any length, Ultra-TrackPans may be used to collect small spills and leaks or to capture and channel off significant spills caused by defective equipment or a major overflow.

• Prevent Costly Cleanup and Regulatory Fines.
• Slip-Resistant Design - Entire top surface is safe to walk on, even when wet or oily.
• All polyethylene construction - Rugged TrackPans withstand harsh chemicals and are designed to function in temperatures ranging from -40º F to +140º F.
• Sealed System - Polyethylene gaskets keep spills from falling between the rails and Pans.
• Trucks and other vehicles can drive over TrackPans with grates in place.*

 *To drive over TrackPans, firm footing must be beneath the Pans; also must "ramp up" side Pans with asphalt or concrete.

Optional T rackPan Covers Keep Rainwater Out Of The Pans, Providing Effective Stormwater Management
Unique stormwater feature is designed to eliminate "pooling" of rain that falls on top of the Center Pan Covers; rain is channeled onto the ballast between the tracks, stays out of the Pans.

• Meets SPCC and EPA Stormwater Management Regulations.
• Also meets New York State Chemical Bulk Storage Regulation Section 599.17c - Secondary Containment for Transfer Stations.

• Low Maintenance - Unlike carbon steel track pans, TrackPans will not rust or corrode, Polyethylene resin is treated with a UV inhibitor, resists degrading effects of the sun,
• Low Cost Installation - Lightweight TrackPans can be easily installed without heavy lifting equipment, i.e., forklifts, cranes, backhoes, etc. Minimal tools and labor required.
• Slip Resistant Surfaces - Pans, grates and covers have been designed with safety in mind. All top surfaces resist slips when wet or oily.
• Long Work Life - Estimated to perform for 20-30 years; longer than fiberglass pans.

TrackPans with Grates, No Covers

TrackPan Covers Only

Options

Part# 9566:
Center TrackPan with Grates
(Includes 2 bulkhead fittings, 4 gaskets, 2 grates)
Dimensions: 53 1/2" x 53 1/2" x 6"
Weight: 106 lbs.
Containment Capacity: 18 gallons

Part# 9580:
Cover for Center TrackPan
Dimensions: 56" x 54"
Weight: 24 lbs.

Part# 9584:
Rebar Fasteners with Protective Cap, 20-Pack

Part# 9559:
3" dia. Bulkhead Fitting (for below-grade piping)

Part# 9586:
Sorbent Mats, Center Pan (2/set),10-Pack

Part# 9576:
Side TrackPan with Grate
(Includes 1 bulkhead fitting, 2 gaskets, 1 grate)
Dimensions: 53 1/2" x 27 1/2" x 6"
Weight: 60 lbs.
Containment Capacity: 19 gallons

Part# 9581:
Cover for Side TrackPan
Dimensions: 56" x 27 3/4"
Weight: 11 lbs.

Part# 9585:
Sorbent Mats, Side Pan, 20-Pack

Part# 9571: Grate Only for Center Pan (Left)
Part# 9572: Grate Only for Center Pan (Right)

Part# 9573:
Grate Only for Side Pan

NOTE: Ultra TrackPans can also be ordered as complete systems: Popular 9-foot, 40-foot and 60-foot systems are available.

• Entry and exit walls are supported every 12" with a patented "living hinge"
• Once a vehicle has entered or exited, the walls automatically spring back to their vertical position.
• Both long sidewalls are held upright by PVC sidewall assemblies. Simply swivel the feet to lower the sidewalls for storage or transport to another location.
• Meets SPCC Regulations.

Dimensions

Part #

Weight

Containment Capacity

12' x 60' x 1'

8505

309 lbs.

5,385 gallons

15' x 50' x 1'

8506

326 lbs.

5,610 gallons

15' x 66' x 1'

8507

405 lbs.

7,405 gallons

Options: Ground Tarps, Track Belts. Self-Bailer (see previous page for self bailer).

Economical Design Offers Cost Savings and Secure Containment

• The Collapsible Wall Model Containment Berm features rugged PVC sidewall assemblies for sidewall support. Simply swivel the "feet" of the PVC supports to lower or raise the sidewalls in just seconds!
• Custom sizes available.
• Standard material of construction is Copolymer 2000™
• Meets SPCC and EPA Container Storage Regulations 40 CFR 264.175.

Dimensions

Part#

Weight

Containment Capacity

4' x 6' X 1'

8405

43 lbs.

179 gallons

6' x 6' X 1'

8403

46 lbs.

269 gallons

10' x 10' X 1'

8400

78 lbs.

748 gallons

12' x 60' x 1'

8404

323 lbs.

5,385 gallons

15' x 50' x 1'

8401

319 lbs.

5,610 gallons

15' x 66' x 1'

8402

420 lbs.

7,405 gallons

Options: Ground Tarps, Track Belts, Protective Storage Bags. Self-Bailer, (see previous page).

• Reinforcing mesh is "sandwiched" between layers of polyurethane - increases durability and resistance to tearing.
• Unique, urethane construction allows the pad to deform and seal off most drains - temporarily "seals" to any smooth surface.
• A valuable addition to any emergency response plan, spill kit, SPCC or stormwater management program.
• Unlike some alternative products, BOTH sides will quickly seal drains - there is no specified "top" or "bottom.”

ULTRA-DRAINSEALS

ULTRA-DRAINSEAL WALLMOUNT

Flexible, non-absorbing material with reinforced, tear-resistant mesh
One unit per box, easily cuts to special shapes and sizes
Resists oil, water and most aggressive chemicals, cleans with soap and water
Prevents contaminants from entering drain
Helps comply with SPCC
Helps comply with NPDES

Square:
Part# 2126: 18" x 18" x 3/8" • 5 lbs.
Part# 2127: 24" x 24" x 3/8" • 9 lbs.
Part# 2130: 36" x 36" x 3/8" • 10 lbs.
Part# 2131: 42" x 42" x 3/8" • 20 lbs.
Part# 2132: 48" x 48" x 3/8" • 34 lbs.
Part# 2133: 54" x 54" x 3/8" • 41 lbs.

Part# 2140: Fits 18" x 18", 24" x 24", .12" dia. and 20" dia. DrainSeals
Part# 2142: Fits 36" x 36" and 30" dia. DrainSeals
Part# 2143: Fits 42" x 42", 48" x 48" and 42" dia. DrainSeals

Circular:
Part# 2134: 12" dia. x 3/8" • 2 1/2 lbs.
Part# 2135: 20" dia. x 3/8" • 5 lbs.
Part# 2136: 30" dia. x 3/8" • 10 lbs.
Part# 2137: 4.2" dia. x 3/8" • 20 lbs.

Made of durable polyethylene. Velcro strap allows quick and easy access.

Non-slip handle for easy carrying.
Mounting hardware included.

Rectangular:
Part# 2124: 18" x 58" x 3/8" • 16 lbs.
Part# 2125: 36" x 58" x 3/8" • 30 lbs.

Temporary Berm Seals Off Spills From The Environment, Nearby Drains And Doorways

• Standard 10-foot sections can be cut to various lengths to meet custom needs.
• Unique, urethane material "weeps" into small cracks and crevices to seal off liquid flow.
• Spill Berm is non-absorbing and is easily cleaned for repeated use.
• Applications include:
• Spill response
• Temporary secondary containment
• Sealing off of doorways during washdown operations
• Flexible Ultra-Spill Berm will bend and turn to form almost any shape while temporarily "bonding" to any smooth surface.
• Helps comply with NPDES and SPCC.

Part# 2100: Orange • Part# 2050: Black

Dimensions: 10' x 4" x 2 1/4"

Weight: 31 lbs. per unit

Material: Non-absorbing polyurethane

Optional connectors (Part # 2101) are used to connect 10' sections

Optional Corners (Part# 2102) are used with Connectors to make 90° corners

Bung Access Funnel
The Bung Access Ultra-Funnel allows access to the 3/4" drum bung. Installation of our pop-up liquid level gauge in the 3/4" bung allows visual monitoring of waste level in the drum and helps you plan ahead for drum removal. It also eliminates the mess caused by overfilling!

Part# 0482: with spout
Part# 0488: no spout
Part# 0484: with hinged cover, with spout
Part# 0487: with hinged cover, no spout

Dimensions: 23 5/8" OD x 5 1/2"
29" x 26 3/4" x 9 1/2" with hinged cover

Weight: 9 lbs.
13 lbs. with hinged cover

Capacity: 6 gallons

Options: Snap-on Cover, Part# 0485
PopUp Fill Gauge, Part# 9985

Burp-Free Funnel
Burp-Free Ultra-Funnels feature a built-in vent. No more splashing or "burping" when pouring liquids!

• Threaded brass insert screws into 2" drum bung.
• All polyethylene construction won't rust or corrode - provides excellent chemical resistance.
• Hinged, lockable lid prevents unauthorized access.
• New, larger style provides bigger pouring area and easy access.

Part# 0651 : Standard

Weight: 5 Ibs.

Dimensions: 13 3/8" dia. x 11" H

Part# 0656: Large

Weight: 8 Ibs.

Dimensions: 22" dia. x 11 1/2" H

Passively Filter Hydrocarbons From Stormwater In Outdoor Containment Products

• The best protection for non-monitored containment sites.
• Helps eliminate problems associated with the collection of rainwater in outdoor containment products.
• Simple installation - can be connected to any outdoor containment product.
• Hydrocarbon "sheens" and modest spills are captured ­clean stormwater drains through the outflow port.
• Larger or concentrated spills activate "auto-shutoff" mechanism.
• Manual shutoff valve can be used to secure all draining operations, change out the filter cartridge.
• Filters are quickly and easily replaced.

Part# 9935: standard

Part# 9937: large

Part# 9926: XL

Part# 9928: XXL

Dimensions: 28" L x 3 1/2" dia.

Dimensions: 36" Lx 4 1/2" dia.

Dimensions: 39" Lx 6 1/2" dia.

Dimensions: 43" L x 9" dia.

Weight: 2 lbs.

Weight: 7 lbs.

Weight: 11 lbs.

Weight: 16 lbs.

Flow Rate: 7.5 gallons per hour*
Material: PVC

Flow Rate: 22 gallons per hour*
Material: PVC

Flow Rate: 42 gallons per hour*
Material: PVC

Flow Rate: 55 gallons per hour*
Material: PVC

Replacement Filter Cartridges
2-Pack Part #9936

Replacement Filter Cartridge
1-Pack Part #9938

Replacement Filter Cartridge
1-Pack Part #9927

Replacement Filter Cartridge
1-Pack Part #9929