Comply With Regulations While Storing IBC Tanks Outdoors

• Upper roll-top door and lower swing-out doors combine to allow easy and convenient access to 1Be.
• Safely stores an IBC tank with maximum dimensions of 52" x 52" x 61".
• low profile (28" height), 360 gallon containment sump allows safe material handling and dispensing.
• Forkliftable, lockable, all-polyethylene design will not rust or corrode.
• Helps meet new Stormwater Management Regulations ­NPDES, 40 CFR 122.26 (1999).
• Meets SPCC and EPA Container Storage Regulation 40 CFR 264.175.

Part# 1162: no drain

Weight: 525 lbs.

Part# 1161: with drain

Containment Capacity: 360 gallons

Outside Dimensions: 64 1/2" x 62" x 96"

Uniformly Distributed Load: 8,500 lbs.

Outdoor Storage for Two IBC Tanks

• Uses same sump as Ultra-Twin IBC SpillPallet (see above).
• Unique, lockable, dual closure allows quick access to tanks.
• Roll-top covers can be easily lifted for routine visual inspection.
• Swing-out doors provide safety and convenience for loading / unloading tanks.
• Safely stores IBC tanks, with maximum dimensions of 52" x 52" x 61".
• Meets Stormwater, SPCC and EPA Containment Regulations.

Part# 1148: no drain
Part# 1149: with drain

Weight: 1167 lbs.

Sump Capacity: 535 gallons
Weight Capacity: 8,000 lbs. UDL/side

Dimensions: 128" x 67" x 96"

Option: Bucket Shelf, Part# 1160

The Only Low-Profile Polyethylene Spill Pallet Strong Enough to Handle Full IBCs

• Capture small leaks and nuisance spills from IRCs.
• Keeps floors free from drips and small spills - eliminates OSHA slip hazards for hazardous and non-hazardous 'spills.
• 4-way forklift entry.
• Translucent sidewalls offer convenient visual leak detection.
• Large 52" x 52" usable deck space accommodates all sizes and shapes of IBCs.

Part# 9630: no drain

Part# 9631 : with drain

Dimensions: 62" x 62" x 8 3/4"

Weight: 125 Ibs,

Uniformly Distributed Load: 9,000 Ibs.

Containment Capacity: 75 gallons

Passively Filter Hydrocarbons From Stormwater In Outdoor Containment Products

• The best protection for non-monitored containment sites.
• Helps eliminate problems associated with the collection of rainwater in outdoor containment products.
• Simple installation - can be connected to any outdoor containment product.
• Hydrocarbon "sheens" and modest spills are captured ­clean stormwater drains through the outflow port.
• Larger or concentrated spills activate "auto-shutoff" mechanism.
• Manual shutoff valve can be used to secure all draining operations, change out the filter cartridge.
• Filters are quickly and easily replaced.

Part# 9935: standard

Part# 9937: large

Part# 9926: XL

Part# 9928: XXL

Dimensions: 28" L x 3 1/2" dia.

Dimensions: 36" Lx 4 1/2" dia.

Dimensions: 39" Lx 6 1/2" dia.

Dimensions: 43" L x 9" dia.

Weight: 2 lbs.

Weight: 7 lbs.

Weight: 11 lbs.

Weight: 16 lbs.

Flow Rate: 7.5 gallons per hour*
Material: PVC

Flow Rate: 22 gallons per hour*
Material: PVC

Flow Rate: 42 gallons per hour*
Material: PVC

Flow Rate: 55 gallons per hour*
Material: PVC

Replacement Filter Cartridges
2-Pack Part #9936

Replacement Filter Cartridge
1-Pack Part #9938

Replacement Filter Cartridge
1-Pack Part #9927

Replacement Filter Cartridge
1-Pack Part #9929

Complete Containment For 275-Gallon Oval Tanks ­ Indoors Or Outdoors!

• Eliminate costly spills while storing fuels, oils and other hazardous liquids.
• Rugged, all polyethylene construction will not rust or corrode.
• Meets EPA Container Storage Regulation 40 CFR 264.175.
• Helps comply with SPCC and NPDES, 40 CFR 122.26 (1999).
• Pullover Cover option keeps rainwater out, yet allows easy access for pumping waste collection activities.

Part# 2800: no drain Part# 2801: with drain

Outside Dimensions: 84 1/2" x 433/4" x 29"; Inside Top: 80" x 39"; Inside Bottom 73" x 31"

Weight: 90 lbs.

Containment Capacity: 360 gallons

Optional PullOver Cover, Part# 2810

Secondary Containment for 500 and 550 Gallon Fuel Tanks

• Economical containment for 500 and 550 gallon fuel and oil tanks.
• 100% polyethylene construction will not rust or corrode - provides superior chemical and weather resistance.
• Optional 3/4" drain fitting available.
• Use with optional Ultra-Self Bailer (Part# 9935) for outdoor containment - Self Bailer allows clean stormwater to passively drain from sump while capturing hydrocarbons.
• Meets Stormwater, SPCC and EPA Containment Regulations.

Outside Dimensions: 87" x 62 1/4" x 32 3/4". Inside Bottom: 75 3/4" x 47 3/4".

Versatile Secondary Containment For Small Containers And Packages

• Low profile, 16.5 gallon sump is perfect for containment of 5-gallon pails, batteries, safety cans, dry cleaning waste drums and leaky machine parts.
• Optional 2' x 4' grating elevates containers from spilled liquid - features 14 gallon capacity with grating.
• Meets EPA Container Storage Regulations for small packages with grating in place.

Ultra-Containment Tray without grating

Ultra-Containment Tray with grating

Part# 2351: Yellow
Part# 2328: Black

Part# 2352: Yellow
Part# 2350: Black

Dimensions: 54" x 29 3/4" x 3 1/2"

Dimensions: 54" x 29 3/4" x 3 1/2"

Weight: 17 lbs.

Weight: 34 lbs.

Containment Capacity: 16.5 gallons

Containment Capacity: 14 gallons

• Countertop spill collection tray safely stores bottles, beakers and other labware.
• Makes decanting of small quantity liquids safer, cleaner and more manageable.
• Features built-in pouring spout to conveniently remove spills.
• Designed for use in research, laboratory, medical and industrial facilities.

Part# 1060: SpiliTray P2

Part# 1061: SpillTray P4

Capacity: 1.8 gallons

Capacity: 2.9 gallons

Weight: 4 lbs.

Weight: 6.5 lbs.

Dimensions: 17" x 12" x 4"

Dimensions: 21" x 17" x 4"

13 1/8" x 8 1/2" usable surface

17 1/8" x 13 1/8" usable surface

• Keeps floors free of spills - designed to collect and contain drips and overflows associated with filling of 55 and 30 gallon drums.
• Optional bottom grate elevates drums 2 5/8" and out of spilled liquid.
• Meets EPA Container Storage Regulations for 20 gallon or smaller containers with bottom grate in place.

Options Available: Bottom Grate, Dolly

Keep Messy Drips and Spills Off Warehouse and Factory Floors

• Heavy-duty polyethylene construction ­ will not rust or corrode.
• Ribbed bottom keeps cans, pails and other containers elevated above any spills or leaks.
• Stackable for easy storage when not in use.
• Available in six sizes for a variety of applications.

Part# 1033: 30" x 48" x 4 3/4" ID • 30 gallons

Mobile Secondary Container Provides Maximum Protection For The Inner Drum

• Applications include satellite waste collection, general storage of chemical drums and portable drum pumping stations.
• Rugged design allows Flat Bottom Model and Pallet Jack Model to be safely handled by forklift under top flange.
• 66 gallon containment capacity.
• Meets SPCC and EPA Container Storage Regulation 40 CFR 264.175.

Part# 1041 : Pallet Jack Model

Part# 1040: Flat Bottom Model

Dimensions: 32 1/2" outside dia.
24 1/4" dia. opening
28 5/8" outside height

Dimensions: 34" outside dia.
24 1/4" dia. opening
27 1/4" outside height

Containment Capacity: 66 gallons

Containment Capacity: 66 gallons

Weight: 28 Ibs.

Weight: 27 Ibs.

Handling:
May be handled with narrow pallet jack.
May be lifted with forklift under top flange.

Handling:
May be lifted with forklift under top flange.
May be wheeled with optional dolly.

Options: Drain Fitting, Dolly (Fits Flat Bottom Model Only)

Mobile System Provides Convenience to Waste Collection Activities

• Three-piece system includes Bung Access Funnel, SpillCollector and Dolly. *
• Can be used with steel or poly 55-gallon drums.
• Meets SPCC and EPA Container Storage Regulation 40 CFR 264.175.
• Entire Systems can be quickly relocated for easier dispensing and collection.
• Add HardTop Cover (Part #9643) for versatile, lockable indoor/ outdoor use.

Part# 9645

Weight: 61 lbs.

Dimensions: 34" x 34" x 44"

Weight Capacity: 1,000 lbs.

Containment Capacity: 66 gallons

Economical SpillSumps Capture Nuisance Leaks and Spills

• Available in 2- and 4- drum sizes.
• Keep plant floor clean, reduce accident risk.
• All polyethylene construction offers excellent chemical resistance.
• Double-stack 55 gallon drums ­saves storage and transportation costs.

Ultra-SpillSump P2

Ultra-SpillSump P4

Part# 9600

Part# 9601

Dimensions: 49 1/2" x 24 3/4" x 5 3/4"

Dimensions: 49 1/2" x 49 1/2" x 5 3/4"

Weight: 15 lbs.

Weight: 25 lbs.

Containment Capacity: 24 gallons

Containment Capacity: 48 gallons

Drum Handling, Dispensing and Containment in One Unit

• Rugged polyethylene construction offers excellent chemical resistance.
• Unlike alternative products, the open containment sump does not require spills to flow inside the double walls to meet EPA regulations - easy to clean; eliminates residue concerns as related to compatibility.
• Can be used with 55- or 30-gallon drums - nylon strap keeps drums secure.
• Ergonomically designed for safe and easy handling.
• large 10" wheels roll easily over shop and factory floors.
• Part# 1312 has large, pneumatic wheels for soft or uneven surfaces.
• large containment sump (66 gallons) meets SPCC and EPA Containment Regulations.

Versatile Utility Box Can Be Used For Spill Kits, Storage Bins and Much More!

• large, 15 cu. ft. capacity.
• Forkliftable and lockable.
• Heavy-duty, double-walled lid is sloped to shed rain.
• Optional casters available.
• Outside dimensions: 48" L x 31" D
  Height without wheels: 31 1/2"
  Height with 5" wheels: 38"
  Height with 8" wheels: 41 3/4
• Available in forest green, safety orange and yellow.

Part#

Description

Weight

0860

Forest Green, no wheels

601bs.

0861

Safety Orange, no wheels

601bs.

0862

Yellow, no wheels

601bs.

0863

Forest Green,S" solid rubber wheels

681bs.

0864

Safety Orange,S" solid rubber wheels

681bs.

0865

Yellow,S" solid rubber wheels

681bs.

0866

Forest Green, 8" pneumatic wheels

921bs.

0867

Safety Orange, 8" pneumatic wheels

921bs.

0868

Yellow, 8" pneumatic wheels

921bs.

Versatile Ultra-OverPacks® Offer The
Highest UN And DOT Certifications Available

• 95-, 55-, 30- and 20-gallon models comply with UN Packaging Group 1 (X-Rating) and are certified for use as DOT Salvage Drums, 49 CFR 173.3 (c).
• High-density polyethylene construction offers excellent chemical resistance, including acids, caustics and corrosives.
• Convenient, "no-tools-required" closures are perfect for clean-up and spill response activities.
• Nestable design and low tare weight allow convenient storage and reduced transportation costs.

Applications Include: • Overpacking of Damaged or Leaking Packages • Collection and Transport of Soiled Sorbents • Clean-up of Contaminated Sites • Emergency Response • Direct Containment and Transport of Hazardous Solids • Use as Spill Kits

All Ultra-OverPacks® Are Independently Certified For:

Part# 0500: 95 Gallon

Part# 0526: 55 Gallon

Part# 0510: 30 Gallon

Part# 0600: 20 Gallon

Top Outside Dia: 31"

Top Outside Dia: 24 7/8"

Top Outside Dia: 21 3/4"

Top Outside Dia: 21 3/4"

Bottom Outside Dia: 25 1/8"

Bottom Outside Dia: 20"

Bottom Outside Dia: 17"

Bottom Outside Dia: 17 3/4"

Outside Height: 43 1/4"

Outside Height: 37 1/2"

Outside Height: 28 1/4"

Outside Height: 16 3/4"

Weight: 47 lbs.

Weight: 23 lbs.

Weight: 17.5 lbs.

Weight: 15.5 lbs.

Rated Capacity: 95 gallons

Rated Capacity: 55 gallons

Rated Capacity: 30 gallons

Rated Capacity: 20 gallons

UN Marking:
1 H2/X340/S/02/USN+AA0959

UN Marking:
1 H2/X204/S/02/USN+AA 1201

UN Marking:
1 H2/X136/S/02/USN+AA0940

UN Marking:
1 H2/X70.8/S/02/USN+AA 117 5

Overpack for Spill Kits

Carry Ultra-OverPacks® Under Trailers For Quick Response To Any Transportation Spill

• Store spill response products inside the 95- gallon Ultra-OverPacks - sorbents, PopUp Pools, Drum Tourniquets and protective clothing are kept clean and moisture-free, ready for action.
• TruckMount Brackets are lockable for security purposes.
• Pre-drilled units can be quickly bolted to trailer undercarriage. (Hardware included)

Waiting for a hazmat response vehicle can be costly - be proactive and equip your trucks with Ultra-TruckMount Brackets!

Bung Access Funnel
The Bung Access Ultra-Funnel allows access to the 3/4" drum bung. Installation of our pop-up liquid level gauge in the 3/4" bung allows visual monitoring of waste level in the drum and helps you plan ahead for drum removal. It also eliminates the mess caused by overfilling!

Part# 0482: with spout
Part# 0488: no spout
Part# 0484: with hinged cover, with spout
Part# 0487: with hinged cover, no spout

Dimensions: 23 5/8" OD x 5 1/2"
29" x 26 3/4" x 9 1/2" with hinged cover

Weight: 9 lbs.
13 lbs. with hinged cover

Capacity: 6 gallons

Options: Snap-on Cover, Part# 0485
PopUp Fill Gauge, Part# 9985

Burp-Free Funnel
Burp-Free Ultra-Funnels feature a built-in vent. No more splashing or "burping" when pouring liquids!

• Threaded brass insert screws into 2" drum bung.
• All polyethylene construction won't rust or corrode - provides excellent chemical resistance.
• Hinged, lockable lid prevents unauthorized access.
• New, larger style provides bigger pouring area and easy access.

Part# 0651 : Standard

Weight: 5 Ibs.

Dimensions: 13 3/8" dia. x 11" H

Part# 0656: Large

Weight: 8 Ibs.

Dimensions: 22" dia. x 11 1/2" H

• Securely fits nearly every 55-gallon tighthead steel or polyethylene drum manufactured throughout the world.
• Unique bottom design fits tightly on drums with varying diameters - no more wobbles or drips!

Part# 0497: with spout
Part# 0499: with hinged cover, with spout

Weight: 13 lbs. without cover
18 lbs. with cover

Capacity: 5 gallons

Options: PopUp Fill Gauge,
Part# 9985 Snap-on Cover, Part# 0498

Open Head Funnel

• All polyethylene funnel can be used on 55-gallon open-head steel or poly drums.
• Replaces drum lid allowing convenient drum access for pouring, collecting rags, soiled absorbents, etc.
• Molded base fits securely onto drum - thumb screws quickly tighten for added security.
• Hinged cover is lockable.

• Nuisance pump drips and overspills flow back into drum without removing funnel.
• Filter screen keeps debris and particles from entering drum.
• Pump adapter fits 2" drum bungs and pumps up to 1 5/8" diameter (pump not included).
• Use with Bung Access Funnel, Part# 0488 (see page 42 for specifications). Funnel must be purchased separately.

Eliminate Vapor Escape While Decanting Wastes
Volatile organic compounds (VOC's) typically evaporate into the atmosphere when waste chemicals are decanted into a drum or when the drum bung is left open. No longer. The Ultra-VaporLock Closure is specifically designed to trap those vapors and eliminate or significantly reduce fugitive emissions.

Easy to install - simply slide fill tube through 2" drum bung and securely thread bushing into drum bung. T-handle is easily hand-threaded into the bushing to seal off potential vapor escape within seconds!

Ultra· VaporLock helps meet EPA Closed Container Regulations. Optional polyethylene fill tube allows filling below liquid level, eliminating agitation and splashing which contribute significantly to the evaporation process.

Ultra-Vaporlock, with Fill Tube

Ultra-Vaporlock, no Fill Tube

Part# 0440

Part# 0444

Dimensions: 35 1/2" x 1 3/4" OD

Dimensions: 6" x 1 3/4" OD

Weight: 3 Ibs.

Weight: 1 lb.

• Securely grips 55 gallon steel drums when loading and unloading salvage drums.
• Rugged, all-steel construction.

• Residual liquids flow to one side of drum for efficient pumping - valuable chemicals can be used, not wasted
• Durable, all polyethylene construction - designed for use with 30 gallon or 55 gallon drums.

Stop Drum leaks On The Spot!
Powerful magnets latch onto steel drums to seal off puncture and corrosion leaks. A chemical-resistant sealing pad is compressed against the damaged area to stop leaks on contact.

Both Models

Magnetic Model Part# 2010

Universal Model Part# 2013

Stainless steel backing plate

Weight: 5 Ibs.

Weight: 9 Ibs.

EDPM sealing pad.
Chemical compatibility guide available upon request.

Dimensions:
22 1/2" x 6 1/2" x 2 7/8"

Dimensions:
22 1/2" x 6 1/2" x 2 7/8"

For temporary use only.
Maximum sealing area: 3 1/2" x 7"

2 magnets, spark resistant assembly

2 magnets, spark resistant assembly.
10 foot long ratchet strap

UV-Resistant bag included

For use on steel drums and other ferrous applications

For use on steel, polyethylene and fiber drums

No tools required

No tools required

Stop leaks From Overturned Tanker Trucks, Railcars And Other large Vessels

Both Models

Magnetic Model Part# 2000

Suction Model Part# 2005

Stainless steel backing plate

Dimensions: 15 3/4" x 32 1/4" x 3 1/4"

Dimensions: 18 1/2" x 33" x 4 1/4"

EDPM sealing bladder. Chemical compatibility guide available upon request.

Weight: 26 Ibs.

8 EPDM suction assemblies

8 magnets, spark resistant assembly

Weight: 18 lbs.

For temporary use only. Maximum sealing area: 3-1/2"x 16"

For use on ferrous vessels

For use on non-ferrous vessels with a non-textured surface (aluminum, stainless steel)

Pressure Pump included

Pressure Pump included

• Reinforcing mesh is "sandwiched" between layers of polyurethane - increases durability and resistance to tearing.
• Unique, urethane construction allows the pad to deform and seal off most drains - temporarily "seals" to any smooth surface.
• A valuable addition to any emergency response plan, spill kit, SPCC or stormwater management program.
• Unlike some alternative products, BOTH sides will quickly seal drains - there is no specified "top" or "bottom.”

ULTRA-DRAINSEALS

ULTRA-DRAINSEAL WALLMOUNT

Flexible, non-absorbing material with reinforced, tear-resistant mesh
One unit per box, easily cuts to special shapes and sizes
Resists oil, water and most aggressive chemicals, cleans with soap and water
Prevents contaminants from entering drain
Helps comply with SPCC
Helps comply with NPDES

Square:
Part# 2126: 18" x 18" x 3/8" • 5 lbs.
Part# 2127: 24" x 24" x 3/8" • 9 lbs.
Part# 2130: 36" x 36" x 3/8" • 10 lbs.
Part# 2131: 42" x 42" x 3/8" • 20 lbs.
Part# 2132: 48" x 48" x 3/8" • 34 lbs.
Part# 2133: 54" x 54" x 3/8" • 41 lbs.

Part# 2140: Fits 18" x 18", 24" x 24", .12" dia. and 20" dia. DrainSeals
Part# 2142: Fits 36" x 36" and 30" dia. DrainSeals
Part# 2143: Fits 42" x 42", 48" x 48" and 42" dia. DrainSeals

Circular:
Part# 2134: 12" dia. x 3/8" • 2 1/2 lbs.
Part# 2135: 20" dia. x 3/8" • 5 lbs.
Part# 2136: 30" dia. x 3/8" • 10 lbs.
Part# 2137: 4.2" dia. x 3/8" • 20 lbs.

Made of durable polyethylene. Velcro strap allows quick and easy access.

Non-slip handle for easy carrying.
Mounting hardware included.

Rectangular:
Part# 2124: 18" x 58" x 3/8" • 16 lbs.
Part# 2125: 36" x 58" x 3/8" • 30 lbs.

Truck Mounted Container Provides Quick and Easy Access to Ultra-DrainSeals®

• Installs quickly and easily to trailer undercarriage - hardware included.
• Tethered hook and loop fastener secures end cap - allows quick and easy access.
• Polyethylene construction will not rust or corrode.

Part# 2145

Fits 18" x 18", 24" x 24", 12" dia. and 20" dia. DrainSeals

Part#2146

Fits 36" x 36" and 30" dia. DrainSeals

Part#2147

F-its 42" x 42", 48" x 48" and 42" dia. DrainSeals

Ultra-DrainSeal Plus Protects Drains And Can Be left Outside Long-Term

• Urethane bottom layer (same as Ultra-DrainSeal) keeps spills from entering drains.
• Rugged, reinforced PVC top layer provides protection from extended UV exposure and vehicular traffic.
• Excellent for use in parking areas, loading docks and other areas where drains may be driven over.
• Bright yellow color helps identify protected drains.

One unit per box

Resists oil, water and most aggressive chemicals, cleans with soap and water

Prevents contaminants from entering drain

Helps comply with SPCC

Helps comply with NPDES

Square:
Part# 21 66: 18" x 18" • 7 lbs.
Part# 2167: 24" x 24" • 15 lbs.
Part# 2160: 36" x 36" • 16 lbs.
Part# 2161: 42" x 42" • 27 lbs.
Part# 2162: 48" x 48" • 43 lbs.
Part# 2163: 54" x 54" • 53 lbs.

Circular:
Part# 2174: 12" dia. • 4 lbs.
Part# 2175: 20" dia. • 7 lbs.
Part# 2176: 30" dia. • 13 lbs.
Part# 2177: 42" dia. • 26 lbs.

Temporary Berm Seals Off Spills From The Environment, Nearby Drains And Doorways

• Standard 10-foot sections can be cut to various lengths to meet custom needs.
• Unique, urethane material "weeps" into small cracks and crevices to seal off liquid flow.
• Spill Berm is non-absorbing and is easily cleaned for repeated use.
• Applications include:
• Spill response
• Temporary secondary containment
• Sealing off of doorways during washdown operations
• Flexible Ultra-Spill Berm will bend and turn to form almost any shape while temporarily "bonding" to any smooth surface.
• Helps comply with NPDES and SPCC.

Part# 2100: Orange • Part# 2050: Black

Dimensions: 10' x 4" x 2 1/4"

Weight: 31 lbs. per unit

Material: Non-absorbing polyurethane

Optional connectors (Part # 2101) are used to connect 10' sections

Optional Corners (Part# 2102) are used with Connectors to make 90° corners

Taller Spill Berm Helps Contain or Divert Larger Volume Spills

• Flexible polyurethane construction is non-absorbent and chemical resistant - easily cleans with soap and water for repeated uses.
• Built-in connectors allow multiple 5-foot units to be quickly and easily connected.
• Helps comply with NPDES and SPCC.

Non-Absorbing Berm Stops Machine Leaks From Spreading

• 1 3/8" tall berm contains leaks, reduces slip hazards.
• Allows quick and easy cleanup or recycling of liquids.
• Flexible, urethane design will bend to follow any curve or angle needed.

Part# 2052

Capture Small Spills Before They Hit The Floor!

• 3/4" tall "mini berm" bends to form any shape.
• Non-absorbing urethane design allows easy clean up.
• Designed for use in laboratory, research, medical and industrial applications.

Part# 2051

Economical Water-Filled Booms Help Contain and Divert Liquids

• Heavy-duty booms fill quickly and easily with water when needed to divert or contain spills.
• Reusable units can be drained for compact storage.
• Available in several sizes ­optional connector can be used to connect two or more units together.
• Rugged, 20 mil PVC construction can be used on smooth or rough surfaces.

Part# 2150

5" dia. X 5' L, Box of 2

1 lb.

Part# 2151

5" dia. X 10' L

1 lb.

Part# 2154

10" dia. X 25' L

3 lbs.

Part# 2155

10" dia. X 50' L

6 lbs.

Optional Connectors (Part# 2153 for 5" spillBooms and Part# 2157 for 10" Spill Booms) used to connect units

• Tapered design wedges securely into standard drains to stop any flow.
• Eyebolts are removable, allowing installation of grating with DrainPlug in place.
• Non-absorbing, easily cleaned for repeated use.

Standard Sizes:

2" Diameter ........ Part# 2113

8" Diameter ........ Part# 2118

3" Diameter ........ Part# 2114

10" Diameter ....... Part# 2119

4" Diameter ........ Part# 2115

12" Diameter ....... Part# 2121

6" Diameter ........ Part# 2117

3-Plug Kit' ......... Part# 2116

* (Includes one each of 2", 3" and 4" Ultra-DrainPlugs and Plastic Carrying Case.)

Flexible polyurethane material
Resists oil, water and most aggressive chemicals
Prevents contaminants from entering drain
Non-absorbing material
Cleans with soap and water
Safety orange color

2" dia. conical plug, Weight: 1.5 lbs.

3" dia. conical plug, Weight: 2 lbs.

4" dia. conical plug, Weight: 3 lbs.

6" dia. conical plug, Weight: 8 lbs.

8" dia. conical plug, Weight: 14 lbs.

10" dia. conical plug, Weight: 22 lbs.

12" dia. conical plug, Weight: 32 lbs.

Collapsible Shovels Are Perfect For Spill Kits

• Non-sparking aluminum models break down to fit into spill kits as small as 5-gallon pails. Assemble in just seconds
• Rugged construction allows shoveling of granular sorbents, sludges and contaminated soil.
• Model #0404 features a polyethylene scoop and excellent chemical resistance.

Part #0401 and #0402

Part #0401

Part #0402

Part #0404

Tempered aluminum scoop measuring 10" x 11"

Weight: 1 1/2 Ibs.

Weight: 1 3/4 Ibs.

Weight: 1 3/4 Ibs.

Shaft constructed of aircraft-quality 6061 T6 aluminum

Quick-release shaft and "D" handle

Quick-release, telescoping shaft

Quick-release shaft

Large, sturdy, molded polyethylene "D" grip handle

Assembled Length: 29"

Assembled Length: 39"

Assembled Length: 37"

Constructed of non-sparking materials

Collapsed size: 15" x 10" x 3", fits into 5-gallon or larger spill kits

Collapsed size: 19 1/2"" x 10" x 3", fits into 20- gallon or larger spill kits

Polyethylene scoop and handle, metal shaft

Epoxy Putty Tackles The Toughest Repair Jobs

• Adheres to steel, glass, masonry and most plastics.
• A quick and effective solution to cracks, broken seals and leaks.
• Simply pinch off the amount desired, knead to a uniform gray and press into place.
• Hardens like steel in only one hour!

Product & Packaging

Physical Properties

7" x 7/8" dia. 12 sticks per box. Shipping weight: 4 lbs.

Density: 15 4/5 lbs/gal. (1 9/10 gm/cm³ )

Shear Strength: 700 psi

Storage Conditions

Temp. (Intermittent): 300°F (149°C)

Exothermic reaction at 123°F. Unaffected by cold. Best used when warm.

Modulus of Elasticity: 6 x 10⁵ psi

Tensile Strength: 6,000 psi

Shelf Life

Hardness (Shore D): 85

lzod Impact: 3 ft.-lb./in. of notch

Several years if stored in original tube

Compression Strength: 18,000 psi

Temp. (Continuous): 250°F (121 °C)

PopUp Pools Instantly Expand To Capture leaks From Saddle Tanks, Pipes, Hydraulic lines And Many Other Industrial Incidents
Ultra-PopUp Pools are available in 150, 100, 66 and 20 gallon sizes. Choose Sprung Steel or Economy Models to meet your needs. Simply remove them from their protective carrying case and give them a quick shake - they instantly expand and are ready for response to any emergency.

• Unique, Patented Design­foam ring rises with level of liquid to raise sidewalls.
• Compact folded size ­stores efficiently inside spill kits; handles on storage bag* can also be used to hang on a wall near shipping/receiving docks.
• All polyethylene construction - offers excellent chemical resistance, including diesel fuel, antifreeze, acids, caustics and corrosives.
• Helps minimize environmental damage and related clean-up costs.
• Excellent for response to damaged saddle tanks and cross-over lines, hazmat spills, leaking containers, machinery and piping.
• Other applications include use as a decontamination pool and collection pool for soiled sorbents.

  * Storage bags are included with Sprung Steel Models only. Optional storage bags are available with Economy Models.

Part# 8020, 8022

Part# 8066, 8068

Part# 8100,8102

Part# 8150, 8153

All Models

20 gallon capacity

66 gallon capacity

100 gallon capacity

150 gallon capacity

Chemical-resistant, 10 mil. polyethylene construction
Reusable after proper decontamination

Filled: Wall 8", Top 28", Bottom 35"

Filled: Wall 12", Top 42", Bottom 53"

Filled: Wall 12", Top 53", Bottom 64 1/2"

Filled: Wall 12", Top 64", Bottom 76"

Economy Models are easily rolled into a tight package. Store them inside the optional Ultra-CabMount Container, which can be bolted to the back side of a truck cab

Store PopUp Pools Behind The Cab - Out Of The Way, But Ready For Any Emergency

• Durable, all-polyethylene construction will resist harsh weather effects.
• Cover is lockable for security purposes.
• Store PopUp Pools outside of the cab, preserving valuable interior space for other necessities.

Note: Only Ultra-PopUp Pool Economy Models will fit into CabMount Containers.

Part# 8155

Dimensions: 28 1/4" x 13" x 10 3/4"

Weight: 8 Ibs.

Material: Polyethylene