Western Safety Logo

Western Safety Products, Inc. 505 South Lander St., Seattle, WA 98134
Toll Free: (888) 823-0808 Phone: (206) 264-0808 Fax: (206) 264-4921
Website: http://www.westernsafety.com sales@westernsafety.com

Facebook LogoYouTube LogoTwitter LogoLinked-In Logo

Credit Card Images

Hubbell Power Systems Page 19


For more information, call Western Safety Products at 206-264-0808 or email sales@westernsafety.com.

Loading

Three-Phase Boom Lifts
Three-Phase Boom Lifts
  • Jib-mounted
  • Winch-driven
  • Constant-load monitor
  • 1,200-lb. rating*

Hot-line tool set enables a material-handler boom truck to lift single- or three-phase system conductors. Operator remains in the bucket, positioned to perform such routine jobs as replacing insulators, crossarm or pole.
Available in eight sleeve sizes to fit on boom truck jibs listed below, each complete unit includes:
10' Vertical orange Epoxiglas® mast (4" x 4") and
10' Horizontal gray Epoxirod® support arm (2112" dia.) with four Heavy-Duty Roller-type Wireholders for conventional crossarm construction
and
6' Horizontal gray Epoxirod support arm (2112" dia.) with one additional Wireholder for center mast for armless construction
and
Storage bags for all components above.
For crossarm construction: 10-foot arm attaches at mast top. Fourth wireholder furnished for crossarm-mounted neutral, not shown.
For armless construction: 6-foot arm attaches at proper level on series of mounting holes on mast.
Maximum Ratings, all units Vertical load per wireholder: 300 lb.
*Balanced vertical load: 1,200 lb., includes tool itself

COMPLETE UNITS
Each complete unit includes a jib sleeve in size listed in addition to:
10' Vertical orange Epoxiglas® mast (4" x 4") and
10' Horizontal gray Epoxirod® support arm (2-1/2" dia.) with four Heavy-Duty Roller-type Wireholders for conventional crossarm construction
and
6' Horizontal gray Epoxirod support arm (2-1/2" dia.) with one additional Wireholder for center mast for armless construction
and
Storage bags for all components above.

Weight each: 225 lb./102 kg.

Catalog No.

Truck Application

C4001612

Asplundh: 3-3/4"-dia. jib

C4001613

Telelect: 4-1/4" -dia. jib

C4001664

ALTEC®: 4"-dia. jib

C4001677

Hi-Ranger model 5H*: 2-7/8"-dia. jib

C4001709

Teco or Holan: 4" x 4"-sq. jib

C4001710

Pitman: 4" x 5"-sq. jib

C4001711

R.O. Products: 5-1/4”-dia. jib

C4002719

No Jib Sleeves included. See below for correct size.

*For Hi-Ranger model6H with top-mounted winch, order E4002215 Jib Sleeve, listed below.

Jib Sleeves for Three-Phase Boom Lifts
Jib Sleeves for Three-Phase Boom Lifts

Catalog No.

Jib Application

Weight

E4001651

3-3/4"-dia., as Asplundh

15 lb./6.75 kg.

E4001652

4-1/4"-dia., as Telelect

15 lb./6.75 kg.

E4001678

4"-dia., as ALTEC®

20 lb./9.09 kg.

E4001679

2-7/8"-dia., as Hi-Ranger model 5H

15 lb./6.75 kg.

E4001689

4" x 4"-sq., as Teco or Holan

20 lb./9.09 kg.

E4001714

4" x 5"-sq. as Pitman

20 lb./9.09 kg.

E4001715

5-1/4"-dia., as R.O. Products

20 lb./9.09 kg.

E4001953

4" x 4" Reach All

20 lb./9.09 kg.

E4002215

4" x 4"-sq., as Hi-Ranger model 6H with top-mounted winch

22 lb./10.8 kg.

E4002262

4-3/4"-dia., as Telelect on over- center model trucks

15 lb./6.75 kg.

E4002293

4-1/2”-sq., as Lift-All

22 lb./10.8 kg.

T4002647

4" x 4" ALTEC®

44 lb./21.6 kg.

Boom Mounted Auxiliary Arm
Boom Mounted Auxiliary Arm

The 4" x 4" mast is fitted with a quick mounting assembly which attaches to booms from 5-7/8" x 7-3/8" to 12" x 12", both square and rectangular. The working end of the mast will accept several accessories such as an Epoxiglas® Auxiliary Arm, single lifting wire holder or a sheave for gin work.
The Auxiliary Arm may be swiveled to and locked into any desired position. The single lifting wire holder may also be swiveled to maintain conductor alignment.
The gin sheave will not swivel and is pinned stationary to keep the plane of the sheave in the vertical position at all times.
For use above 15kV, add M48057 insulator to each wire­holder; see below.

Max. Side load per Wireholder: 100 lb.
Max. Vertical Load per Wireholder C4000268:
Arm Length: 10'
With Braces: 200 lb.
Mechanical Rating
Balanced Vertical Load: 1000 lb.
Unbalanced Vertical Load: 800 lb.

Catalog No.

Description

Weight

C4000744

Mast Assy., 10' Arm & Braces for Booms 5-7/8" x 7-3/8" to 12" x 12"

130 lb./58.5 kg.

C4000745

Mast Assembly without Arm

90 lb./41 kg.

C4000746

Rope Sheave Assembly

8 lb./ 3.6 kg.

C4000747

Single Wire Holder

13 lb./ 5.9 kg.

T4001656

Conductor Hook for 2-1/2” jib

3 lb./1.35 kg.

T4001658

Conductor Hook for 3" jib (Altec®)

3 lb./1.35 kg.

C4001469

9"-dia. Boom Adapter (Altec®)

40 lb./18 kg.

C4001877

8"-dia. Boom Adapter (Altec®)

40 lb./18 kg.

Boom Auxiliary Arm
Boom Auxiliary Arm and Attachments

The Auxiliary Arm consists of a boom mast and arm of Epoxiglas® construction for mounting on an insulated boom such as the Pitman Polecat®. The arm is designed for use on light construction when handling multiple conductors. The two-legged mast can be mounted on square or rectangular shaped booms designed to handle 2,000 pounds or more. If boom units of lesser ratings are employed, the lifting and maneuvering application of this unit must be reduced accordingly. Mechanical rating for a balanced vertical load is 1,000 pounds maximum or a limit ofthe boom arm in the position used, whichever is the least. The 10' arm, recommended for use with braces only, is rated at 200 pounds per conductor holder.
Chance C4000268 roller wireholders are used on the Boom Auxiliary Arm and Mast. Each wireholer is rated for 100 lb. max. side load.

H486310

10' Assembly with braces

120 lb/54.0 kg.

H48633

Bipod-Arm clamp only

12-1/2 lb./ 5.6 kg.

H48634

Arm Brace Assembly only

8-3/4 lb./ 3.9 kg.

H4863

4' Bipod Mast only with boom clamps

64 lb./28.8 kg.

C4000351

2-1/2" x 10' Horizontal Arm

13 lb./l0.35 kg.

AUXILIARY ARM ATTACHMENTS
Fork type wireholders - with 1" or 1-1/2" opening, counter balanced latch which closes automatically behind the conductor to hold it in the wireholder. Complete with 2-1/2" pole clamp.
C-Type Wireholder - For rubber glove work, the Chance "C" -type Wireholder is suspended for a 2-1/2" diameter temporary crossarm above the conductor as a hook to receive the conductor after it is untied.
Roller Wireholder - Seven Delrin plastic rollers offer protection to conductors while raising the conductor above the work area. Accommodates conductors up to and including 1-1/2 inches in diameter. The gate is held closed by a spring­loaded latch which must be manually opened.
Insulators- Epoxy based, available as separate items or can be added to existing auxiliary arm wireholders to upgrade for 34.5 kV use.

Catalog No.

Description

Weight

E4000008P

1-1/2" Fork Wireholder, no Insulator

2-1/2 lb./1.1 kg.

M480515

1" Fork Wireholder, with Insulator

5-1/2 lb./2.5 kg.

M480517

1" Fork Wireholder, no Insulator

2 lb./ .9 kg.

M480516

C-Type Wireholder, no Insulator

2-1/2 lb/1.1 kg.

C4000690

Roller Wireholder, no Insulator

4-1/2 lb/2.0 kg.

C4000268

Roller Wireholder, no Insulator

4-1/2 lb/2.0 kg.

M48057

Epoxy Insulator, 7h6" threads

1-1/4 lb./0.55 kg.

Boom Mouted Auxiliary Arm with Load-Monitor System
Auxiliary Arm with Load Monitor

Continuous load readout, audible alarm Load-Monitor System built into lower end of the mast measures and displays the weight of load being lifted, including the Auxiliary-Arm assembly itself. An audible alarm warns truck operator and others nearby should a preset working load be exceeded. Complete operating and maintenance instructions are furnished with each unit.
Typical application enables lifting a three-phase set of conductors out of the way while a pole, crossarm or other equipment is replaced or repaired. Meter permits operator to check the actual load throughout operation. This can be of extreme importance since these conductor loads are difficult to estimate and vary with conductor sizes and tensions, pole spans and terrain geometry. By helping to alert operators to potential overloads, the load-monitor system can help avoid damage to trucks and other equipment while also adding to personnel safety.
Note that mast base casting has "teeth" on both sides so it can be mounted either way around on the boom for optimum visibility of the meter by the operator.
Choice of boom adapters, scales, options Available to fit either round or rectangular booms, both come with hydraulic load gauge scale graduated in either English pounds or metric kilograms.
Optional accessories include a single wireholder and a conductor hook for use on the end of the mast. A rope-sheave assembly also fits the mast for use as a gin. Single wire­holder may be swiveled as needed. Hook swivels, but its base pins for control. Sheave pins to keep it aligned in a vertical-plane.
Load Ratings (mast unit only) Max. balanced vertical load: 1,000 lb. (454 kg.)
Max. side load: 100 lb. (45 kg.) or 30% of actual vertical load if less

Ordering Information
Each Auxiliary Arm listed below comes complete with: Appropriate boom adapter, 70" mast assembly, braces, 10' arm and three wireholders with 2" opening.

Catalog No.

Description

Weight

For Square/Rectangular Booms 5-7/8" x 7-3/8" to 12" x 12":

C4001821E

English scale Auxiliary Arm

135 lb./60.75 kg.

C4001821M

Metric scale Auxiliary Arm

135 lb./60.75 kg.

For Round Booms 9" in Diameter (as Altec):

C4001950E

English scale Auxiliary Arm

135 lb./60.75 kg.

C4001950M

Metric scale Auxiliary Arm

135 lb./60.75 kg.

Accessories

C4000746

Rope Sheave Assembly

8 lb./3.6 kg.

C4000747

Single Wireholder

13 lb./5.9 kg.

T4001658

Conductor Hook for 3" jib

3 lb./1.35 kg.

E4000748

Sq./Rect. Boom Adapter only

40 lb./18 kg.

C4001469

9"-dia. Boom Adapter only

40 lb./18 kg.

Truck Grounding Set
Truck Grounding Set

Convenient set provides means to drain off capacitance or static charges from winch trucks and aerial devices. This grounding method should not be considered adequate protection to personnel against conductor contact. Complete set comprises components selected for their task-specific designs:
Screw Ground Rod (Catalog No. G3370)
When installed 6-ft. copper-clad rod develops less resistance than straight ground rods. Helix (spiral section), T-handle and wingnut are bronze for high conductivity.
Flat Face Ground Clamp
(Catalog No. T6001798)
For secure attachment to the truck bed at an area cleaned for electrical contact, clamp features bronze T-handle, aluminum body and serrated jaws with range for 1/8" to 1-1/2" angles or flats. Ratings: 400 amps continuous current; 25,000 amps fault current for 15 cycles and 30 cycles.
C-Type Ground Clamp
(Catalog No. C6001754)
For connection to vertical shaft of ground rod, clamp fea­tures smooth jaws and bronze eyescrew. Ratings: 350 amps continuous current; 28,000 amps fault current for 15 cycles and 20,000 amps fault current for 30 cycles.
Grounding Cable and Ferrules
(Catalog No. S6116 & C6002618)
For easy handling, extra-flexible #2 copper cable features fine stranding and tough yellow T-prene rubber compound jacket for all-temperature uses down to -20°F. Cable length is 50 feet. Two shrouded aluminum ferrules come factory­installed on the cable to secure the threaded studs in the clamp terminals.
Storage Reel
(Catalog No. C4176086)
To help keep ground set clean and ready for use, reel features tubular-steel frame which can be bolted to deck. Reel is for storage only. Cable and clamps must be removed completely from reel before use. Failure to do so could result in a dangerous voltage drop and violent mechanical reactions. A label on the unit gives this warning.

ORDERING INFORMATION

Catalog No.

Description

Weight

T6001971

Truck Grounding Set

35 lb./15.75 kg.

Swivel Wireholder Jib Extensions for Telelect Trucks*
Swivel Wireholder Jib Extensions for Telelect Trucks

Feature a Large Swivel-Type Roller Wireholder with 2-1/2" x 3-3/8" opening mounted on 3" diameter orange Epoxiglas® jib extension. Tested per ASTM F711 and OSHA.

ORDERING INFORMATION

Catalog No.

Fits Jib Size

Weight

PST4002818

4" x 4"

28 lb. 112.72 kg.

PST4002819

3-3/8" x 5"

29 lb. 113.2 kg.

PST4002820

3" Round

27 lb. 112.3 kg.

PST4002821

4-1/2" Round

28 lb, 112.72 kg.

* To fit other brands of trucks, contact Hubbell Power Systems with detailed specifications.

Bi-Pod Three-Phase Arm H486310
Bi-Pod Three-Phase Arm

Combination Swivel Wireholder/Sheave for ALTEC Trucks
Wireholder/Sheave Combo

By design, each unit eliminates changeovers from Wireholder (for picking up a phase conductor) to Rope Sheave (for lifting items). Each combination unit attaches directly to the jib.
Rated Working Load: 800 lb.
Both units feature a Large Swivel-Type Roller Wire­holder with 2-1/2" x 3-3/8" opening and a 7"-diameter Sheave to accept up to 3/4"-diameter rope.

Illlustrations of Truck Booms & Other Adapters
Boom Adapters for ALTEC Trucks
Boom Adapters for ALTEC Trucks
Three Phase Boom Assembly C4000744
Three Phase Boom Assemblies for ALTEC Trucks T4001753
Boom Adapters for ALTEC Trucks
Boom Adapters for ALTEC Trucks
Auxiliary Arm for ALTEC Trucks
Auxiliary Arm for ALTEC Trucks
Support Arms with fitting for 3" diameter mast
Small Roller Wireholder
Large Roller Wireholder
Heavy Duty Wireholder
ALTEC Jib Adapters
Hi-Ranger Jib Adapter
Small Roller Wireholder with Hi-Ranger Adapter
Large Roller Wireholder with Hi-Ranger Adapter
Heavy Duty Wireholder with Hi-Ranger Adapter
Holan Jib Adapter
Small Roller Wireholder with Holan Adapter
Large Roller Wireholder with Holan Adapter
Heavy Duty Wireholder with Holan Adapter
Telelect Jib Adapter
Small Roller Wireholder for Telelect Jib
Large Roller Wireholder for Telelect Jib
Heavy Duty Wireholder for Telelect Jib
3 inch diameter Jib Extension for ALTEC Trucks
4 x 4 inch Jib Extension for Holan Trucks
4 x 4 inch Jib Extension for Reach-All Trucks

WSP home page Products page Suppliers page  
Electrical Safety Hubbell Power Index Previous Hubbell-Chance Page Next Hubbell-Fargo-Anderson Page