Western Safety Logo

Western Safety Products, Inc. 505 South Lander St., Seattle, WA 98134
Toll Free: (888) 823-0808 Phone: (206) 264-0808 Fax: (206) 264-4921
Website: http://www.westernsafety.com sales@westernsafety.com

Blue Water Manufacturing - Guardrails, Warning Flags, Fall Protection

Loading

Credit Card Images

Safety Rail 2000
Safety Rail Illustration
Roof Edge Fall Protection Cell Workstations and Forklift Runs
Loading Docks and Hazard Platforms
Uses for Safety Rail 2000
Roof Hatch System Skylight System

Meet the world's most versatile Guardrail system — Safety Rail 2000, by Blue Water Manufacturing. Fall protection and barrier protection that protects your investment and complies with OSHA. No drilling required for installation. Can be installed by unskilled labor.

Versatile:

  • Non-penetrating and 100% portable
  • Rails can be secured in infinite directions
  • Each base can support up to 4 rails
  • Unskilled labor can install over 600 feet per hour
  • Custom manufacturing available
  • Galvanized coatings available
  • No tools required for installation
  • Various size gates available to fit your requirements

Safety:

  • Positive locking system secures the rails to the base
  • System exceeds OSHA regulations 29 CFR 1910.23 and 1926.502
  • Toe board adapters available
  • No counterweights are required, thus reducing trip hazards
  • Protection for your employees and visitors
  • Rubber pads available for use on membrane roofs and for smooth concrete surfaces
  • Working handles cast into base

Do Not Void Your Warranty

  • Stop drilling into Roof Decks
  • Stop drilling into Roof Hatches & Skylight Curbs
  • Stop drilling into Floors

Features:

  • Non-Penetrating
  • Independently tested and shown to meet and exceed OSHA Fall Protection Regulations for Guardrails
  • Sets up in minutes
  • The engineered bse enables the system to be set up in numerous configurations (L-Shapes, Straight Runs, etc.)
  • Easily dismantled for roof deck repair
  • The gate can be opened by the latch pole or by one of the latches
  • 1-5/8" diameter rails have a quality powder coat finish
  • Use as roof hatch, skylight, fire vent and floor door protection

In most situations, OSHA (Std. 29 CFR 1910.23) requires guardrail protection on the exposed sides of openings in roofs and floors. BlueWater Mfg. has modified the Safety Rail 2000 guardrail system to meet these safety concerns. The Roof Hatch/Skylight systems exceeds OSHA Std. 29 CFR 1910.23 and 1910.27. It is the only product available in the market with a gate assembly that meets the same OSHA regulations and requires no drilling into any surface for installation. The Roof Hatch/Skylight systems set up in minutes and are easily dismantled for roof repair.

Roof Hatch & Stairway Hatch Kits
Scuttle/Roof Hatch Kits: (Includes: 1 sized gate, 2 sized rail sections, 4 bases and 6 locking pins). Note: on side exit hatches, 4th rail and 2 ea. pins are included
Kit No. Entry Dimensions Length
500043 24" 24"
  24" 30"
  24" 36"
500097 - Side Exit 24" 30"
500098 - Side Exit 24" 30"
500040 30" 30"
500108 - Side Exit 30" 30"
500040 30" 36"
500099 - Side Exit 30" 36"
500046 36" 36"
  36" 48"
500101 - Side Exit 36" 48"
500102 48" 48"
Stairway Hatch Kits: (Includes: 1 sized gate, 3 sized rail sections, 4 bases and 8 locking pins)
500047 30" 54"
500049 36" 60"
500048 30" 96"
500050 36" 96"

Safety Rail Parts
Standard Base Galvanized Base Rail
Std. Base (300014) and BUR Roof Pad (100029) Galv. Base (300037) and EPDM Roof Pad (100034) Rail: 3ft. (500105), 3.5ft. (500106), 4ft. (500104), 5ft. (500001), 10ft. (500005)
Toe Board Bracket Securing Pin EZ Mover
Toe Board Bracket (300025) Securing Pin (100016) EZ Mover (500023)

Ordering Information for Safety Rail 2000
Unless you are making a full enclosure, you will have to order one extra base per set up.
Rail Kits
(Powder coated rails; kit includes: 1 base, 1 rail section and 2 locking pins)
Rail Kits with Toe Board Brackets
(Powder coated rails; kit includes: 1 base, 1 rail section, 2 locking pins, 2 brackets and 2 friction knobs)
Gate Kits
(Powder coated gate kit includes: 1 base, 1 gate assembly and 2 locking pins
500131 3' rail kit 500152 3' rail kit 500091 3' gate kit
500145 3.5' rail kit 500153 3.5' rail kit 500090 3.5' gate kit
500146 4' rail kit 500154 4' rail kit 500149 4' gate kit
500009 5' rail kit 500018 5' rail kit 500010 5' gate kit
500011 7.5' rail kit 500020 7.5' rail kit 500013 10' gate kit
500012 10' rail kit 500021 10' rail kit

 


ParaRail
Easy and Full Access to edges of fall hazards
The new, patent pending ParaRail is a non-penetrating, self supporting system that allows workers full access to a leading edge on a flat roof or the roof's parapet. ParaRail provides fall protection for a variety of tasks, including maintenance for security cameras, antennas, lights, drain cleaning, and hoisting of tools and materials. The new system exceeds OSHA regulations for guardrail (29 CFR 1910.23 and 1923.502).
A new generation component in BlueWater's Safety Rail 2000 Guardrail system, the ParaRail provides the portability and economy of a self supporting, no drill installation. LIke the SafetyRail 2000 Guardrail system, the ParaRail sets up in just a few minutes. With the EZ Mover (bottom right photo in this table), the bases transport easily. Optional rubber pads are available for added protection of roof membranes when desired.
ParaRail enables users to meet OSHA mandates for leading roof edge safety and fall protection with a mobile system. You can use the ParaRail system as a permanent fixture or move it to different locations. It provides the economies of a fully portable system for commercial, industrial and worksite applications including office building, airports, high-rises, parking decks, raised docks, shopping centers, mezzanines, and bridges.
Each ParaRail is manufactured per application. All BlueWater needs to know are the lengths for the dimensions that are shown in the diagram below left, and the desired length of the span. Powder coat or galvanized finishes are available.
Pararail illustration Pararail Photo 1
Pararail Photo 2 Pararail Photo 3


Perma-Line Permanent Visual Warning Line System
Permaline Photo 1 Permaline Photo 2 Permaline Photo 3
The Perma-Line was designed for permanent placement of a Warning Line System for roof fall protection and creating controlled access zones. With this innovating system, you will no longer have to make monthly trips to your rooftop to replace torn or worn out plastic flagging. Once in place, the Perma-Line remains intact until you want to move it. Best of all, it's a non-penetrating system.. The Perma-Line is not a motion stopping device. It is a highly visible warning barrier. It exceeds OSHA regulations for warning line systems.


Steath-Rail - A Non-Penetrating Collapsible Guardrail System
Stealthrail Photo Steathrail Photo 1
Stealthrail Photo 2 Stealthrail Photo 3

The StealthRail is a self-contained collapsible rail section for the SafetyRail 2000 Guardrail system. Its one-way pivot assembly allows the rails to fold onto a surface and then not exceed a vertical plane when in the upright position. A detent pin is attached to each pivot assembly that locks the rails in the upright position. SafetyRail 2000 requires no penetration in substrates for installation. The system exceeds OSHA standards 29 CFR 1926.501 and 1926.502
When the system is in its folded position, there are clean sightlines from ground level and the building's architectural integrity is preserved.

  • Save $$$ over an engineered lifeline system
  • Rails come in 3', 3.5', 4', 5', 7.5' and 10' sections
  • A tough UV yellow powder coat finish comes standard. Other colors and galvanized finishes are available
  • The rails can be mounted in infinite positions
  • Use the system around mechanicals or for perimeter protection
  • Certified test results are available


Kwik-Stand Portable Warning/Barrier System
Kwik-Stand Photo 2 Kwik-Stand Photo 1 Kwik-Stand Photo 3
Extender Feet Shown in use and folded for transport Easy Flag Tie-Off System
The Kwik-Stand is a hand carried warning line system. The self contained design provides for quick set up and removal with no chance of lost parts. The unique spindle mount system gives it rigidity when in use. The handle makes it easy to transport and hoist. The Kwik-Stand comes standard with a tough powder coat finish or galvanized finish to help ensure a rust free product.
The Kwik-Stand has a hole at each end of the support bars. Use for the following: On metal roofs, insert the optional extender feet to fit between the ribs of the roof. On gravel or asphalt, use stakes to make the stand more secure.

Features:

  • Quick Set up
  • "No lose" lanyard clip pin assembly
  • Galvanized finish available
  • Complies with OSHA standard 29 CFR 1926.502 (f)
  • 39" tall when assembled
  • 39" x 32" in use footprint
  • 39" x 2" x 3.5" when folded
  • Each stand weighs 34 lbs.
  • Easy to attach extender feet for metal roofs

Benefits:

  • Provides a high visibility warning to reduce accidents
  • Self contained
  • Fast setup and removal times
  • Complies with regulatory codes
  • Bright yellow OSHA rated flags
  • Optional rubber pads protect flooring
  • Easy flag tie-off system
  • Stores easily

Uses:

  • Rooftops
  • Construction sites
  • Parking lots
  • High rise construction
  • Manufacturing facilities
  • Maintenance contractors
  • Office buildings
  • Amusement parks
  • Airports
  • Warehouses


Kwik-Rail Modular Railing System
Kwik-Rail System
The Kwik-Rail Safety Railing is an economiclly priced handrail system that is easily assembled with just a hex key. Create a tough and durable barrier in just minutes with no welding. The cross members come standard in 6 ft. lengths that give you a lower cost per foot. If 6 ft. is too long for your needs, simply cut the cross members to size. The railing is 42" tall. The systems come in kit form and custom gates can be manufactured. The kits can be secured by off-the-shelf anchoring bolts.

Benefits & Options:

  • Exceeds OSHA and BOCA standards
  • Lower cost per foot
  • Tough powder coated pipe in safety yellow
  • Easily assembled with standard anchor bolts
  • 1-1/2" pipe
  • Various colors
  • Galvanized pipe option
  • Aluminum pipe option
  • 1-1/4" pipe option

Use for:

  • Machine guarding
  • Traffic control
  • Crowd control
  • Elevated docks/pits
  • Stairway landings

Kit Part Numbers:

500136.40: 6 ft. rail only
500137.40: 12 ft. straight run
500138.40: 6 ft x 6 ft corner section
500139.40: 6 ft. extension
500140.40: 6 ft - 90º extension

For 1-1/4" pipe option, replace the .40 with a .32

Versa-Clamp Guardrail System
Versa-Clamp components 1
Versa-Clamp Guardrail Versa-Clamp upright post 1 Versa-Clamp upright post side view

The Versa Clamp is the most versatile guardrail C-Clamp in the marketplace for Fall Protection. Use it on parapets as well as concrete slabs to provide fall protection. The compression plates are off-set so they will not damage copings or flashings on parapets. Its unique compression locking system makes it simple and fast to install. Simply place the clamp over a parapet or on a concrete slab and slide the compression plate against the surface. Turn the compression rod against the plate and you are finished. Make in USA and built tough.

Key Features:

  • Expands from 1" to 12"
  • Simple and fast compression locking system
  • Compression plates are off-set to protect copings and flashings
  • Adjustable guardrail post allows it to comply with OSHA guardrail heights from the work surface
  • Install at 8 foot increments
  • Use on parapets or decking applications
  • Toe board brackets are available for deck applications
  • Adapters for Kwik Rail are available for permanent placement on buildings
  • Tough safety yellow powder coat finish
  • Other colors available to match your building
  • Custom manufacturing available to meet your special requirements

WSP home page Products page Suppliers page
Fall Protection Traffic Control