Legge Systems Page 3

For more information, call Western Safety Products at 206-264-0808 or email sales@westernsafety.com.
We accept VISA and Mastercharge.

LEGMAT 1/8" STATIC DISSIPATIYE WORK SURFACE & FLOOR MATTING

LEGMAT is a homogeneous product-not composed of laminated composites. This quality assures you of quick, safe, static dissipation with no chance of capacitance surge.

The combination of both LEGMAT floor mats and work surface mats provides you with the ultimate protection for your components and equipment. They dissipate damaging electrostatic charge from the human body. Features:
• Permanently Static Dissipative
• Eliminates capacitance surge
• Electrical properties are virtually unaffected by changes in humidity
• Superior heat and flame resistance
• Durable and flexible
• Lays flat Designer Colors Available:

ITEM:  
#3010 - Electronic Blue
#3011 - Designer Ivory
#3012 - Midnight Brown
Sizes Available: 2' x 100', 3' x 100', 4' x 100'

TWO LAYER LEGMAT

ITEM tt3101
Floor and Table Matting
|One side is Static Dissipative, and the other is Conductive. Chemical & Solder Resistant LEGGE's TWO LAYER LEGMAT is a unique design that combines the durability of rubber with the resistance to solder and chemicals required in the demanding environments of today's manufacturing facilities.

TWO LAYER LEGMAT provides excellent static dissipation properties that exceed both EOS/ESD and DOD requirements.

Sizes Available: 2' x 75', 4' x 75'

THREE LAYER LEGMAT

ITEM #3610 -3 Layer

Vinyl matting consisting of a solid static dissipative, vinyl skin and a buried conductive layer. The buried layer provides excellent conductivity without the danger of exposed conductors. Provides constant resistance to ground from any position on the mat. Sizes Available: 2' x 75', 4' x 75'

1/8" LEGMAT

Thickness: Nominal 1/8" 0.120 in.+O.OO5 in.
Weight:  0.94 Ibs./ft.2
Hardness: Shore "A" Durometer ASTM D-2240-75: 70 + or - 3
Tensile Strength ASTM D-412-75: 700 + or - 50 psi
Elongation -100% ASTM D-412-75: 240 + or - 25%
Tear Strength-Die"C" ASTM D-624-73: 100 + or -10 lbs./in.
Wear Resistance/Weight Loss Tabor Abrader 1000 Cycles CS- 17 Wheels 1000 Grams Load: Less than 0.02 grams
Flame Resistance Methenamine Tablet Test DOC-FF1-70: Less than 0.5 in.
Limiting Oxygen Index ASTM D-2863-77: Greater than 27%
FMVSS302: Passes
ELECTRICAL PROPERTIES:
*Resistance to Ground ASTM D-257: 109 ohms
Volume Resistivity ASTM D-257: 108 ohms - cm
**Static Decay Time MILB 81705-C: Less than 0.10 sec.

* Direct resistance reading to ground point on 36 inch diagonal, measured in 2 inch increments using Dr, Kamphausen Mili-to precision Ohm meter at 500 volts.

** The electro-static decay criterion as outlined in MIL B 81705C, and specified in EIA, IS-5 when tested in accordance with FTS 101C method 4046.1 5000 volts to technical 0 volts with 2.0 seconds maximum. The information contained above is generally representative of the product.

TWO LAYER LEGMAT

Resistance from Surface to Ground: 107 -109 ohms EOS/ESD
Std-4 Charge decay time: <.01 seconds Fed Std 101 Met 4046
Surface Resistance: 107 -109 ohms ASTM D257
Point to Point Resistance: 107 -109 ohms EOS/ESD Std-4
Surface Resistance (bottom): <105 ohms ASTM D257
Thickness (Total Mat): .60 +/- .002 inches Tensile Strength: 1000 psi ASTIVI D412
Durometer: 60 ASTM D2240 (Shore A) Chemical Resistance: Excellent (Use LEGGE's CONDUCTIVE CLEANER for daily and as needed cleaning)
Solder Resistance: Excellent (molten solder has no effect)
COLOR: Black/Blue

THREE LAYER LEGMAT

Electrical Properties

Rtg: 10 Volts 1.9 x106 ohms
Rtt: 10 Volts 2.3 x106 ohms
Rtg: 100 Volts 1.6 x106 ohms
Rtt: 100 Volts 2.1 x106 ohms

Physical Properties

Gage: .125 in.
Tensile: 360 PSI Elongation: >125%

Flame Resistance:
Methanamine Tablet Test: <0.5 in.

CONDUCTIVE FLOOR RUNNERS AND TABLE MATS

RIBBED ITEM #3000 SMOOTH ITEM #3003/3004

LEGGE CONDUCTIVE RUNNERS and MATS are made to be used in areas where harsh chemicals and solvents would tend to attack flooring. The inherent solvent resistance of our rubber make them virtually indestructible! Mats are available in full rolls and precut sizes. The runners may be permanently affixed with glue or they can lay on the floor or table without glue so that they may be moved from place to place. Unlike vinyl type mats the LEGGE mat will lie flat and does not become a tripping hazard. In the interest of safety however — some form of clamp or screw may be required if the mat is placed on a slippery surface.
All personnel standing on runners or mats must be wearing body grounding devices to dissipate body static charges. Please refer to body grounding devices. The mats will drain all static from conductors as well as from itself.
Conductive floor runners used within a complete system of static control have reduced failures on sensitive items as well as safe­guarded against explosion and fire hazards due to static electricity discharge.
• Conductivity not effected by humidity or temperature
• Complies to NFPA Code 99-NFPA Method 250,000 ohms
• Surface resistivity of 103 - 105
• Static decay rate less than 0.5 seconds
Diamond Plate matting is designed with beveled edges for firm, flat contact with floor

FLOOR RUNNER

Surface: Smooth
Thickness: 1/8" or 1/4"
Width: 48"
Roll Length: 50' (or precut)
Ohms/sq. in.: 103-105 ohms
Fillers: Carbon
Color: Black

 FLOOR RUNNER

Surface: Ribbed
Thickness: 1/8"
Width: 36"
Roll Length: 75' (or precut)
Ohms/sq. in: 103-105
Fillers: Carbon
Color: Black

ESD MODULAR MAT AND ESD MODULAR DRAINAGE MATTING

Type: Grease resistant rubber compound
Resistance point to point: 1 x 107 Ohms
Charge decay time, 5000 Volts-10 Volts, FTMS 101 C, Method: < 0.01 Seconds
Durometer, Shore 00, ASTMD-2240: 50 Thickness: 1/2"
Color: Black

STATIC DISSIPATIVE AND CONDUCTIVE ANTI-FATIGUE MATTING

ITEM #3017 (Static Dissipative)
ITEM #3018 (Conductive)

Prevents fatigue while protecting components and personnel from damaging electric shock. Use in areas where static discharge can harm materials (static dissipative) or ignite flammable/ explosive materials (conductive). Sponge base reduces stress on spine and lower back muscles caused by standing in one place for extended periods of time.

ESD MODULAR MATS

ITEM #3097 (Modular Drainage)
ITEM #3098 (Modular)

Innovative, Modular Drainage ESD Anti-fatigue Matting. Use in areas where static discharge and slippery/ wet floors are a problem. Use as a single workstation mat or cover an entire floor. Extremely versatile. Designed to greatly reduce loss from static discharge. The proprietary built-in interlocking system requires no connectors or additional bevels and allows the mat to be interlocked vertically or horizontally. Manufactured for comfort and functionality. Modular Drainage design will greatly reduce problems associated with slippery conditions as well as reduce ESD dangers. Rounded corners for easy access.

ANTI-FATIGUE MATTING

#3017 - Static Dissipative
Surface Resistivity: Surface to surface 1 x107 ohms
Surface to ground: 1 x 107 ohms
Size: 3' wide x 1/2" thick x 75' full roll
Color: Gray
Surface: Smooth and diamond plate vinyl

#3018 - Conductive
Surface Resistivity: Surface to surface 1 x 104 ohms
Surface to ground 1 x 104 ohms
Size; 3'x5' precut
3' wide x 1/2" thick x 75' full roll
Color: Black
Surface: Smooth and diamond plate vinyl

  

ANTI-FATIGUE CONDUCTIVE MATTING

ITEM # AFM366658 - size 36" x 66" x 5/8"
ITEM # AFM333658 - size 33" x 66" x 5/8"

The anti-fatigue conductive mat was designed for protection against Electrostatic Discharge (ESD). The sponge rubber mat is conductive for rapid static dis-charge to ground. Resistance readings are well within the specifications called out in DOD and NFPA specifications. The closed cell nitrile material pres-ents excellent resistance to abrasion, oil, grease, and most common solvents. These anti-fatigue mats are scientifically and ergonomically designed to reduce strain from standing on hard surfaces and provide proper orthopedic comfort. Use this high quality mat in harsh work environments where proper static elimination is critical.

Available in black. Two stock sizes with a standard 45° bevel to prevent tripping. Also available as a runner in 3' widths.

CONDUCTIVE INTERLOCK MAT

ITEM #3025

A reliable and economical protection from static discharge.
These mats offer exceptional resistivity: Surface-to-surface — 104 ohm and surface-to-ground — 104 ohm. Specially compounded 1/2" thick rubber is electrically conductive throughout the mats, which are engineered with buoyant air pockets underneath to create a very comfortable work surface. This construction greatly reduces fatigue and other aches and pains related to standing. The sections easily "lock" together to create runners of virtually any size.
The mats are also available in singles for individual workstations and are economically priced. The high-tech deck plate surface is easy to clean yet provides additional traction. Its edges are beveled for safe, easy access.
Color: Black
Stock Sizes: 3' width x 2' length Ends, Singles, Centers

ANTI-FATIGUE CONDUCTIVE MATTING

Type: ESD Sponge anti-fatigue floor mat

Resistance point to point: bottom layer, same: 5 x 105 Ohms
Charge decay time, 5000 Volts-10 Volts, FTMS 10 1 C. Method: < 0.01 Seconds
Durometer, Shore 00, ASTMD-2240: 50
Burn Test, UL94 HBF: Passed
Extinguished in 10 sec., burned 1/4"
Thickness: 5/8"
Color: Black

CONDUCTIVE INTERLOCK MAT

Surface Resisitivity:

Surface to Surface -1 x 104 ohms
Surface to Ground -1 x 104 ohms
Size: Stock size is 3' X 2', Ends, Singles, Centers
Color: Black
Surface: Deck Plate

LEGTOP DECORATIVE STATIC DISSIPATIVE LAMINATE

LEGTOP is a hard Laminate manufactured with the electronics and clean room industries in mind. This high pressure laminate is designed to provide extraordinary resistance to sliding abrasion, with extreme hardness and extended durability — typical requirements of work surfaces in the electronic industries.
The unusual hardness of the LEGTOP surface, eliminates the possibility of contamination in a clean room environment. The prevention of loose particle generation during sliding abrasion is a fundamental require ment in the clean room environment — LEGTOP meets this requirement.

LEGTOP DECORATIVE STATIC DISSIPATIVE LAMINATE

Surface Resistivity: Typical ASTM D257 103-105
Resistance to Ground Ohms: NFPA-99 103- 105
Decay Rate: 5000 to 0 Volts - .5 sec. (Fed Test Method 101C-4046 0.01)
Wear Resistance: (NEMA 1 d-3-1985) Legtop Conventional
Typical Nema Value 1550 Cycles
Typical Rate of Wear 600 Cycles
(Weight loss per 100 Cycles Abrasion): .006 gm/100 cycles
Thickness: .032 post formed or .050
Formability: Postformable within 1/2" to 3/4" radius depending on equipment and humidity
Sizes: 4'x10'; 3'x10'; 5'x10'; 4'x12'; 3'x12', 5'x12'
Chemical Resistance: Resistant to common solvents such as: Acetone; 111 Trichloroethylene; Solder Flux; IsopropyI Alcohol; Naphtha
Temperature Resistance: 350° F with no change per NEMA LD-3.08. Molten solder will not mar surface
Color: Soft White, Beige, Blue, Grey

*Laminate must be grounded to be effective, assembled structure must be tested for continuity to ground to ensure functionality. One (1) megohm current limiting resistor must be installed in series with the ground to provide personnel protection.

FIELD SERVICE KIT

ITEM #FSK-1

The LEGGE FIELD SERVICE KIT (FSK) permits field technicians to perform repairs on a static free surface. The FSK prevents and dissipates static charges that are potentially harmful to sensitive components. The black side of the FSK is conductive, while the green side is static dissipative. This design allows the charges to effectively drain off the static dissipative surface to the conductive side and then to ground through the included ground strap. A common ground point is provided so that the technician can connect a Wriststrap (included) to the FSK. This arrangement ensures that the surfaces and the technician are at the same electrical potential — further minimizing potential damage to sensitive components. Very durable and made to be folded and transported from one location to another. The material meets all conductivity and static decay specifications of MIL-B81705B and NFPA ff56A.

IMPORTANT INSTRUCTIONS FOR ALL MATTING

• All LEGGE Static Dissipative and Conductive Mats and work surfaces should always be cleaned regularly with LEGGE CONDUCTIVE CLEANER only to avoid soil and debris buildup.
• LEGMAT should be connected to suitable ground for maximum effectiveness. Workers should use one meg ohm resistor type WRISTAT or LEG STRAP.
• Common household and commercial cleaners should be avoided due to the possibility of build-up on the surface of the matting. This build-up may insulate the matting and reduce the ability to discharge static electricity.

FIELD SERVICE KIT

Electrically Conductive Antibacterial Fabric Properties Test Method Results

Face: 1.0 x 107 Ohms, (NFPA): #56A-73 Para 4631
Back: 3 x103
Bacterial, Fungal, and Mildew Resistance: Excellent
Primary Skin Irritation Index: 0 Draize Dermal Toxicity
Weight: 10.00 oz.per sq. yd.
Flame Resistance: 1.5 sec. after flame & glow time
Char Length: 5.3 in.
Breaking Strength: 85 lbs. / 1 in. 5100
Tear Resistance: 30 Ibs 5134 & HTM 4.2.3
Abrasion Resistance: 3.8 5304,5201 & HTM 4.2.2
• Two months accelerated aging @ 160
• Five days immersion in #30 motor oil
• Fifteen minutes immersion in ethyl ether
• Low humidity (desiccated) - 4 week exposure
• Washing with 2% soap solution - 24 cycles
• Exposure to 24 common antiseptics
• Autoclaving
• Series of flex tests
Dimensions: 24" x 24"

WSP home page Products page Suppliers page  
Electrical Protection Legge Index Previous Legge Page Next Legge Page