For more information, call Western Safety Products at 206-264-0808 or email sales@westernsafety.com.
 |
 |
| GFR1205 Freeze resistant emergency shower, plastic shower head GFR1206 Freeze resistant emergency shower, plastic shower head, piping included |
GFR1814 Freeze resistant eye wash, wall mounted, stainless steel bowl GFR1814P Freeze resistant eye wash, wall mounted, plastic bowl |
| Application: Freeze resistant emergency shower for horizontal mounting. Valve and supply line are located behind wall in heated area to prevent freezing. Since unit is intended for use in cold weather conditions, consideration should be given to supplying unit with tempered water in accordance with ANSI Z358.1-2004. See "Tempering Units" section for more info Shower Head: 10" diameter. Shower head is orange ABS plastic (GFR1205) or stainless steel (GFR1205SSH) Valve: 1" IPS chrome plated brass stay open ball valve. Valve is US made with chrome plated brass ball and Teflon seals. Valve handle is mounted on extension rod that projects through wall. Specify wall thickness when ordering Pipe and Fittings: Supplied by others Supply: 1" NPT female inlet Sign: ANSI-compliant identification sign Available options: |
Application: Freeze resistant eye wash for wall mounting. Valve and supply line are located behind wall in heated area to prevent freezing. Self draining valve permits water to drain completely from unit after use. Since unit is intended for use in cold weather conditions, consideration should be given to supplying unit with tempered water in accordance with ANSI Z358.1-2004. See "Tempering Units" section for more information Spray Head Assembly: Two GS-Plus™ spray heads. Each head has "flip top" dust cover and internal flow control Valve: 1/2" IPS chrome plated brass three way self draining stay open ball valve. Valve is US made with chrome plated brass ball and Teflon seals. Valve has 1/2" NPT female drain port. Valve handle is mounted on extension rod that projects through wall. Specify wall thickness when ordering Bowl: 11-1/2" diameter. Bowl is stainless steel (GFR1814) or orange ABS plastic (GFR1814P) Mounting: Heavy duty cast aluminum wall bracket with corrosion resistant powder coated finish Supply: 1/2" NPT female inlet Waste: 1-1/4" NPT female outlet Sign: ANSI-compliant identification sign Quality Assurance: Unit is completely assembled and water tested prior to shipment Availble options: |
 |
 |
| GFR1825 Freeze resistant eyewash, pedestal mounted, stainless steel bowl GFR1825P Freeze resistant eyewash, pedestal mounted, plastic bowl |
GFR1902 Freeze resistant safety station with eye wash GFR1909 Freeze resistant safety station with WideArea™ eye/face wash |
| Application: Freeze resistant eye wash for pedestal mounting. Freeze resistant valve and supply line are buried below frost line to protect against freezing. Unit is designed to drain completely after use, so that no standing water remains in unit and possibility of freeze up is eliminated. Since unit is intended for use in cold weather conditions, consideration should be given to supplying unit with tempered water in accordance with ANSI Z358.1-2004. See "Tempering Units" section for more information Spray Head Assembly: Two GS-Plus™ spray heads. Each head has a "flip top" dust cover and internal flow control Valve: 3/4" IPS freeze resistant valve with push plate. Valve body and supply line are buried below frost line to prevent freezing. Valve has 1/4" IPS bleed outlet to permit water standing in unit to drain out after use. Specify bury depth of valve when ordering Bowl: 11-1/2" diameter. Bowl is stainless steel (GFR1825) or orange ABS plastic (GFR1825P) Pipe and Fittings: Schedule 40 galvanized steel. Furnished with orange polyethylene covers for vertical piping for high visibility and corrosion resistance Supply: 3/4" NPT male inlet Waste: 1-1/4" NPT female outlet Sign: ANSI-compliant identification sign Quality Assurance: Valve and spray head assemblies are factory assembled and water tested prior to shipment Available options: |
Application: Freeze resistant combination eye wash and shower safety station. Freeze resistant valves and supply lines are buried below frost line to protect against freezing. Unit is designed to drain completely after use, so that no standing water remains in unit and possibility of freeze-up is eliminated. Since unit is intended for use in cold weather conditions, consideration should be given to supplying unit with tempered water in accordance with ANSI Z358.1-2004. See "Tempering Units" section for more information Shower Head: 10" diameter orange ABS plastic Shower Valve: 1-1/4" IPS freeze resistant valve with push plate. Valve body and supply line are buried below frost line to prevent freezing. Valve has 1/4" IPS bleed outlet to permit water standing in unit to drain out after use. Specify bury depth of valve when ordering Spray Head Assembly: Two GS-Plus™ spray heads (GFR1902) or four GS-Plus™ spray heads (GFR1909). Each spray head has a "flip top" dust cover and internal flow control Eye Wash Bowl: 11-1/2" diameter stainless steel Eye Wash Valve: 3/4" IPS freeze resistant valve with push plate. Valve body and supply line are buried below frost line to prevent freezing. Valve has 1/4" IPS bleed outlet to permit water standing in unit to drain out after use. Specify bury depth of valve when ordering Pipe and Fittings: Schedule 40 galvanized steel. Furnished with orange polyethylene covers for vertical piping for high visibility and corrosion resistance Supply: 3/4" NPT (eye wash valve) and 1-1/4" NPT (shower valve) male inlets Waste: 1-1/4" NPT female outlet Sign: ANSI-compliant identification sign Quality Assurance: Valve and spray head assemblies are factory assembled and water tested prior to shipment Available options: |
 |
| GFR3100 Heated safety station with eye/face wash, top inlet GFR3110 Heated safety station with eye/face wash, bottom inlet |
| Application: In areas where electricity is available, heat-traced safety stations provide excellent protection against freezing. Units are heated by self limiting heat tracing cable wrapped around internal pipe. Thermostat regulates heating. Units are insulated and jacketed for protection against weather. Since unit is intended for use in cold weather conditions, consideration should be given to supplying unit with tempered water in accordance with ANSI Z358.1-2004. See "Tempering Units" section for more information Shower Head: 10" diameter orange ABS plastic with 20 GPM flow control Shower Valve: 1" IPS brass stay open ball valve. Valve is US made with chrome plated brass ball and Teflon seals. Furnished with stainless steel actuating arm and 29" stainless steel pull rod Spray Head Assembly: Two FS-Plus™ spray heads. Each spray head has a "flip top" dust cover and internal flow control Eye/Face Wash Valve: 1/2" IPS brass three way self draining stay open ball valve. Valve is US made with chrome plated brass ball and Teflon seals. Valve has 1/2" NPT female drain port to permit water to drain away from spray heads after use Jacket/Insulation: UV resistant orange ABS plastic jacket with removable polyethylene foam insulation. Furnished with elastomeric seals for all seams and openings in jacket Heating Cable: Self regulating heat tracing cable with external braid guards. Heating is controlled by thermostat that shuts off heat when ambient temperature is over 50ºF. Cable is FM and CSA approved Electrical System: Unit is fully wired at the factory. Junction box and components are rated for Class 1, Division 2, Groups B, C and D. System requires a 120 VAC, 60 Hz single phase power supply Pipe and Fittings: Schedule 40 galvanized steel Supply: 1-1/4" NPT female top inlet Sign: ANSI-compliant identification sign Quality Assurance: Unit is fully assembled and factory tested prior to shipment Available options: |
 |
 |
| G1512 10 gallon portable eye wash/drench hose unit G1511 10 gallon portable eye wash unit |
G1522 15 gallon portable eye wash/drench hose unit G1521 15 gallon portable eye wash unit G1520 15 gallon portable drench hose unit |
| Application: Self contained eye wash and/or drench hose units that are ideal where a continuous supply of potable water is not available. These units may be used in low traffic areas, low hazard areas or where installation of plumbed equipment is not cost effective. Ten gallon units provide approximately 8.3 usable gallons of water for effective rinsing of eyes, face or body. Note that, under ANSI Z358.1-2004, drench hose units supplement but do not replace other types of emergency equipment Tank: 10 gallon stainless steel pressurized tank. Tank has built-in carrying handles, air intake fitting, pressure gauge and pressure relief valve. Tank has approximately 8.3 gallons usable capacity Eye Wash Unit: Two GS-Plus™ spray heads, each with a "flip top" dust cover, internal flow control and filter. 1/2" IPS chrome plated brass stay open ball valve with flag handle. Eye wash delivers 0.5 GPM for 15 minutes Drench Hose: Single GS-Plus™ spray head with "flip top" dust cover, internal flow control and filter. Chrome plated brass squeeze valve with stainless steel lever handle and 6 ft. reinforced PVC hose. Drench hose is furnished on G1512 only Operation: To operate unit, fill with clean potable water and add bacteriostatic additive (supplied with unit). Additive protects against growth of bacteria, fungus, algae and acanthamoeba inside unit. After filling with water, pressurize unit to 80 psi air pressure. Unit should be inspected regularly and water in unit should be changed at least once every six months Weight: 22 lbs. empty; 91 lbs. filled Quality Assurance: Unit is completely assembled, pressurized and water tested prior to shipment Available options: |
Application: Self contained eye wash and/or drench hose units that are ideal where a continuous supply of potable water is not available. These units may be used in low traffic areas, low hazard areas or where installation of plumbed equipment is not cost effective. Ten gallon units provide approximately 12.8 usable gallons of water for effective rinsing of eyes, face or body. Note that, under ANSI Z358.1-2004, drench hose units supplement but do not replace other types of emergency equipment Tank: 15 gallon stainless steel pressurized tank. Tank has built-in carrying handles, air intake fitting, pressure gauge and pressure relief valve. Tank has approximately 12.3 gallons usable capacity Eye Wash Unit: Two GS-Plus™ spray heads, each with a "flip top" dust cover, internal flow control and filter. 1/2" IPS chrome plated brass stay open ball valve with flag handle. Eye wash delivers 0.8 GPM for 15 minutes Drench Hose: Single GS-Plus™ spray head with "flip top" dust cover, internal flow control and filter. Chrome plated brass squeeze valve with stainless steel lever handle and 6 ft. reinforced PVC hose. Operation: To operate unit, fill with clean potable water and add bacteriostatic additive (supplied with unit). Additive protects against growth of bacteria, fungus, algae and acanthamoeba inside unit. After filling with water, pressurize unit to 80 psi air pressure. Unit should be inspected regularly and water in unit should be changed at least once every six months Weight: 28 lbs. empty; 134 lbs. filled Quality Assurance: Unit is completely assembled, pressurized and water tested prior to shipment Available options: |
 |
|
Introducing the G1562 portable eyewash for rinsing the eyes, face, or body. With fifteen gallon capacity, the G1562 is fully compliant with ANSI Z358.1 as an eyewash and has the unmatched durability of a keg. The first time in history a keg is synonymous with safety. APPLICATION: Self-contained eyewash and/or drench hose units are ideal where a continuous supply of potable water is not available. These units may be used in low traffic areas, low hazard areas or where installation of plumbed equipment is not cost effective. Fifteen gallon units provide approximately 10 usable gallons (37-9 liters) of water for effective rinsing |
|
| Available Options | |
| G1540BA | 8 oz. bottle of bacteriostatic additive to protect against growth of bacteria and other impurities in portable unit. |
| HC | Two wheel hand cart for transporting and storing unit. |
 |
| G1540 AquaGuard™ gravity flow portable eye wash, 16 gallon |
| Application: Self contained 16 gallon eye wash unit uses gravity to deliver water through dual spray heads. Unit delivers over fourteen gallons of water for 15 minutes, thus complying with the provisions of ANSI Z358.1-2004 for eye washes. Unit has a rugged plastic tank that can be installed in a wide variety of locations. Unit is ideal for use where a continuous supply of potable water is not available, especially in remote plant areas, low traffic and/or low hazard areas. Tank: 16 gallon capacity safety green polyethylene tank. Tank has built-in carrying handle, heavy wall construction and reinforced ribs to support weight of unit Spray Head Assembly: Water flow is activated by pulling down on bright yellow eye wash tray. Integral full flow nozzles deliver soft spray of water. Swing tray up to storage position to stop flow. Drain: Waste water is directed into drain opening in tank basin. 3 ft. long drain hose directs discharge into floor drain, storage tank or other receptor Mounting: Furnished with epoxy coated steel bracket for mounting unit on wall. Unit can also be placed on countertop or other flat surface Preparation: To operate unit, fill unit with clean, potable water and add bacteriostatic additive (supplied with unit). Additive protects against growth of bacteria, fungus, algae and acanthamoeba. Unit should be inspected regularly and water in unit should be changed at least once every six months Discharge Time: Eye wash delivers 0.7 GPM for 15 minutes Weight: 19 lbs. empty, 145 lbs. full Quality Assurance: Unit is completely assembled and water tested prior to shipment Available options: |
 |
 |
| G1100 EyeSafe™ faucet mounted eye wash, adjustable aerated outlet heads |
G1101 EyeSafe-X™ faucet mounted eye wash, adjustable aerated outlet heads |
| Application: EyeSafe™ faucet mounted eye washes convert any faucet into an emergency eye wash station without interfering with normal faucet operation. An EyeSafe™ unit can be installed at any sink, close to where accidents might occur. In an emergency, unit is quickly located and activated, and provides an unlimited supply of potable water for rinsing the user's eyes Outlet Heads: Outlet heads are mounted 3" apart and deliver a soft, aerated flow of water. Heads angle forward towards user. Angle of heads is adjustable to permit full coverage and avoid splashing. Furnished with float-off dust covers to protect outlet heads Valve: Forged brass diverter valve. Pull knob to activate eye wash; water pressure holds eye wash in operation, leaving user's hands free. Push knob or turn off faucet to return to normal faucet operation Inlet: Body has 55/64"-27 female thread. Furnished with three adaptors (15/16"-27, 13/16"-27 and 3/8" IPS for installing on most commonly used faucets, including laboratory type faucets Outlet: Furnished with removable aerator on bottom Quality Assurance: Each unit is completely assembled and water tested prior to shipment Available options: IMPORTANT! |
Application: EyeSafe™ faucet mounted eye washes convert any faucet into an emergency eye wash station without interfering with normal faucet operation. An EyeSafe™ unit can be installed at any sink, close to where accidents might occur. In an emergency, unit is quickly located and activated, and provides an unlimited supply of potable water for rinsing the user's eyes Outlet Heads: Outlet heads are mounted 5" apart and deliver a soft, aerated flow of water. Heads angle forward towards user. Angle of heads is adjustable to permit full coverage and avoid splashing. Furnished with float-off dust covers to protect outlet heads Valve: Forged brass diverter valve. Pull knob to activate eye wash; water pressure holds eye wash in operation, leaving user's hands free. Push knob or turn off faucet to return to normal faucet operation Inlet: Body has 55/64"-27 female thread. Furnished with three adaptors (15/16"-27, 13/16"-27 and 3/8" IPS for installing on most commonly used faucets, including laboratory type faucets Outlet: Furnished with removable aerator on bottom Quality Assurance: Each unit is completely assembled and water tested prior to shipment Available options: IMPORTANT! |
 |
| G1102 EyeSafe-A™ Faucet mounted eye wash, non-adjustable solid stream heads |
| Application: EyeSafe™ faucet mounted eye washes convert any faucet into an emergency eye wash station without interfering with normal faucet operation. An EyeSafe™ unit can be installed at any sink, close to where accidents might occur. In an emergency, unit is quickly located and activated, and provides an unlimited supply of potable water for rinsing the user's eyes Outlet Heads: Outlet heads are mounted 3" apart. Heads deliver a non-aerated, solid stream of water. Angle of heads is not adjustable. Furnished with float-off dust covers to protect outlet heads Valve: Forged brass diverter valve. Pull knob to activate eye wash; water pressure holds eye wash in operation, leaving user's hands free. Push knob or turn off faucet to return to normal faucet operation Inlet: Body has 55/64"-27 female thread. Furnished with three adaptors (15/16"-27, 13/16"-27 and 3/8" IPS for installing on most commonly used faucets, including laboratory type faucets Outlet: Furnished with removable aerator on bottom Quality Assurance: Each unit is completely assembled and water tested prior to shipment Available options: IMPORTANT! |
 |
 |
| G3600 Tempering valve, 6 gallon capacity G3602 Tempering valve, 6 gallon capacity, surface mounted stainless steel cabinet G3607 Tempering valve, 6 gallon capacity, recess mounted stainless stee cabinet |
G3800 Tempering valve, 44 gallon capacity G3802 Tempering valve, 44 gallon capacity, surface mounted stainless steel cabinet G3807 Tempering valve, 44 gallon capacity, recess mounted stainless steel cabinet |
| Application: Tempering valve to blend hot and cold water to deliver tepid water. Valve has flow capacity of 0.5 to 6 gallons per minute. Valve can be used with eye wash, eye/face wash, dual purpose eye wash/drench hose and drench hose units Temperature Control: Valve has bimetallic thermostat that senses incoming water temperature and automatically blends water to 85ºF. High temperature limit is set to 90ºF. Valve has dial thermometer on outlet to monitor temperature of delivered water. Note: Valve may need to be adjusted when installed based on incoming water temperature. Refer to installation instructions for further information Fail Safe: In event of restriction or failure of hot water supply, internal bypass allows valve to deliver cold water to emergency unit. In bypass mode, valve will 4 GPM of cold water at 30 psi flow pressure. In event of loss of cold water supply, valve will close and not deliver water Flow Capacity: Refer to chart below this table for flow capacity of valve at specified pressure drops Supply Pressure: 30 psi minimum supply pressure is required for proper operation of valve. Maximum supply pressure is 125 psi Mounting: G3600 is furnished with heavy duty mounting bracket for securing valve to panel or wall. G3602 has valve installed in surface mounted stainless steel cabinet. G3607 has valve installed in recess mounted stainless steel cabinet Inlets: 1/2" OD copper female hot and cold water inlets. Each inlet has check valve installed in recess mounted stainless steel cabinet Outlet: 1/2" NPT female outlet Quality Assurance: Valve is completely assembled and water tested prior to shipment |
Application: Tempering valve to blend hot and cold water to deliver tepid water. Valve has flow capacity of 3.0 to 44 gallons per minute. Valve can be used with eye wash, eye/face wash, dual purpose eye wash/drench hose and drench hose units Temperature Control: Valve has bimetallic thermostat that senses incoming water temperature and automatically blends water to 85ºF. High temperature limit is set to 90ºF. Valve has dial thermometer on outlet to monitor temperature of delivered water. Note: Valve may need to be adjusted when installed based on incoming water temperature. Refer to installation instructions for further information Fail Safe: In event of restriction or failure of hot water supply, internal bypass allows valve to deliver cold water to emergency unit. In bypass mode, valve will 20 GPM of cold water at 30 psi flow pressure. In event of loss of cold water supply, valve will close and not deliver water Flow Capacity: Refer to chart below this table for flow capacity of valve at specified pressure drops Supply Pressure: 30 psi minimum supply pressure is required for proper operation of valve. Maximum supply pressure is 125 psi Mounting: G3800 is furnished with heavy duty mounting bracket for securing valve to panel or wall. G3802 has valve installed in surface mounted stainless steel cabinet. G3807 has valve installed in recess mounted stainless steel cabinet Inlets: 1" NPT female hot and cold water inlets. Inlets can be rotated 360 degrees for top or bottom supply. Each inlet has integral water strainer, check valve and supply stop Outlet: 1-1/4" NPT female outlet Quality Assurance: Valve is completely assembled and water tested prior to shipment |
 |
| G3900 Tempering valve, 81 gallon capacity G3902 Termpering valve, 81 gallon capacity, surface mounted stainless steel cabinet G3907 Tempering valve, 81 gallon capacity, recess mounted stainless steel cabinet |
| Application: Tempering valve to blend hot and cold water to deliver tepid water. Valve has flow capacity of 3.0 to 81 gallons per minute. Valve can be used with eye wash, eye/face wash, dual purpose eye wash/drench hose and drench hose units Temperature Control: Valve has bimetallic thermostat that senses incoming water temperature and automatically blends water to 85ºF. High temperature limit is set to 90ºF. Valve has dial thermometer on outlet to monitor temperature of delivered water. Note: Valve may need to be adjusted when installed based on incoming water temperature. Refer to installation instructions for further information Fail Safe: In event of restriction or failure of hot water supply, internal bypass allows valve to deliver cold water to emergency unit. In bypass mode, valve will 40 GPM of cold water at 30 psi flow pressure. In event of loss of cold water supply, valve will close and not deliver water Flow Capacity: Refer to chart below this table for flow capacity of valve at specified pressure drops Supply Pressure: 30 psi minimum supply pressure is required for proper operation of valve. Maximum supply pressure is 125 psi Mounting: G3900 is furnished with heavy duty mounting bracket for securing valve to panel or wall. G3902 has valve installed in surface mounted stainless steel cabinet. G3907 has valve installed in recess mounted stainless steel cabinet Inlets: 1-1/4" NPT female hot and cold water inlets. Inlets can be rotated 360 degrees for top or bottom supply. Each inlet has integral water strainer, check valve and supply stop Outlet: 1-1/4" NPT female outlet Quality Assurance: Valve is completely assembled and water tested prior to shipment |
| WSP home page | Products page | Suppliers page | |
| Emergency Showers & Eyewash |
Guardian Index | Previous Guardian Page |
Next Guardian Page |