For more information, call Western Safety Products at 206-264-0808 or email sales@westernsafety.com.
DBI - SALA Fall Protection and Rescue Systems
 |
 |
 |
Finally, a rope grab that is truly "mobile", working just as good on swelled and worn rope as on new.
|
||
| Easy Installation: Simply remove the detent pin, open the hinge and place the rope grab on the 5/8" lifeline. Then insert the detent pin back in and connect your 3 ft. EZ-STOP II shock absorbing lanyard to the rope grab and to the back D-ring of your harness. The rope grab incorporates a "gravity latch" mechanism preventing the device from being installed upside down. Easy to Use: Once the system is installed, the rope grab will travel freely up and down the lifeline hands free, eliminating manual repositioning. The worker is safely protected along the entire length of vertical lifeline. The inertia and cam locking systems are much safer than single locking systems. The shock absorbing design also results in lower arresting forces on the worker in the event of a fall. Easy to Remove, Relocate, Handle and Store: The rope grab can be attached or removed at any point on the lifeline making it very convenient and easy to use. Simply remove pin, open hinge and remove from lifeline for relocation or storage. Versatile and Economical: This lightweight system is reusable and transportable from one job site to another. The revolutionary design enables it to be used on worn or new rope without any of those nuisance lockups. Complete with compatible connection point for your lanyard, reducing the chance of roll out. |
||
| 5000335 | Rope Grab for use on 5/8" lifeline | |
| 5002042 | Rope Grab with attached 3 ft. EZ-STOP Shock absorbing lanyard | |
| 5000400 | Rope Grab System; 5000335 Rope Grab, 50 ft. 1202794 Lifeline, 5901583 Flexible Counter-weight, 1220007 3 ft. Shock Absorbing Lanyard, 1003000 3 ft. Tie-Off Adapter, 9511597 Carrying Bag | |
| 5000401 | 5000400 system except with 100 ft 1202844 Lifeline and 9503806 Carrying Bag | |
| Multispan Sayfline Horizontal Lifeline Systems
Finally, a simple and safe "off the shelf" multispan horizontal lifeline designed for user installation. It's an economical solution for non engineered "home made" systems and those requiring costly third party installation. Exceeds all applicable OSHA and ANSI requirements. In-line Zorbit Energy Absorber reduces anchorage point strength requirements and provides added worker safety. |
Tilt Wall Horizontal Lifeline Systems
A simple and safe horizontal system designed to provide tilt wall installation workers their needed protection. Stanchions simply bolt directly to the prefabricated lifting holes in the wall. Exceeds all applicable OSHA and ANSI requirements. |
|||||||||||||||||||||||||||||||||||||||||
 |
 |
|||||||||||||||||||||||||||||||||||||||||
| Part # 7603040 Multispan Sayfline Horizontal Lifeline System | Part # 7008501 Tilt Wall Horizontal Lifeline System | |||||||||||||||||||||||||||||||||||||||||
Similar models: 7603060 60 ft. system |
Complete System:
|
|||||||||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||||||||
| BeamSafe
Designed with the help of craftsmen in the field, the BeamSafe system gives you an easy to install tie-off point before flooring or other fall protection is available. Position the BeamSafe system almost anywhere on a beam for both fall protection and as a hand rail for balance for up to two people. Installing the system is quick and easy, requiring just a standard wrench to assemble the two bolts and a safety strap. Each lightweight stantion, weighing less than 35 lbs., mounts at a 19 degree angle from the base to keep it out of the way while walking the beam. |
Iron Wing
The easy to install and fully customizable Iron Wing sytem is ideal for larger beams and multispan lengthy systems and is carefully engineered for contiuous fall protection while giving you freedom of movement. DBI-SALA's 3-point claw / contact system offers reliability without tie-back, reducing trip fall hazards. |
|
 |
 |
|
Part # 7400520 Complete BeamSafe System
Similar Models: 7400530 30 foot system |
Part # 7003020
Similar Models: 7003030 30 foot system Custom systems: 7006606 Stantion with energy absorber For custome orders, the last three digits of part # details length of cable |
 |
||||||||||||||||||||||||||
| Part # 7003560 Horizontal Concrete Lifeline System
Complete system includes 60 foot line, stanchions, cable assembly and Zorbit energy absorber (last 2 digits in part number indicate length. Available in 10 foot increments) 7006334 Additional stanchion - end anchor 7006333 Additional Tie-back assembly (must use with stanchion on each end of system) 7006335 I-Beam Adapter Base — 10" to 25" flange width, 1/2" to 3" thick Simply place the stanchion base attachment blocks around the rebar and tighten using a torque wrench (75 ft./lbs.). Once the tie back system is installed to the stanchion and beam, the cable lifeline is attached. Then hook up and you're ready to go. Once the system is installed, simply attach one of our industry preferred shock absorbing lanyards or Talon SRL directly to the lifeline and to the D-ring on your harness. The system is completely reusable and transportable from one job site to another. It is completely adjustable, fitting most rebar sizes from #3 to #6, 2.5" to 12" center to center.
|
||||||||||||||||||||||||||
 |
| Part # 2200500 Complete Vacuum Anchor System
|
Finally! a mobile fall arrest anchor that provides mechanics in the aircraft industry with a safe way to work on the wings, fuselage, and tail sections of planes.
|
|
 |
Electric Vacuum Anchor System with Cart
2200030: Cart |
 |
Electric Vacuum Anchor System with Pelican Cases
9500478: Pelican Case for Pads (29" X 17-7/8" X 10-1/2") |
 |
Compressed Air Vacuum Anchor System / Pneumatic
2200050: Compressed Air / Pneumatic Vacuum Pump |
 |
Horizontal Vacuum Anchor System
Choose one of the systems above and add the following: 2200025: Second Vacuum Anchor Pad Assembly |
 |
| • Self Contained Vacuum Anchor System (Part #: 2200046) The Self Contained Vacuum Anchor System is a uniquely portable and self contained fall arrest rated anchor that enables personnel to work at height and stay connected to the structure. System consists of one single component – no multiple parts and components to get lost or misplaced. Patent Pending. • Versatile and portable system can be used indoors or out. No need for fixed overhead lines that just get in the way. A lightweight (32 lbs.) unit makes attachment and transport effortless. • Optional bottle option allows system to be used totally independent of all power sources. No need for electrical or pneumatic power sources with bottle option. • Can be used in conjunction with secondary pad 2200047 to create up to 40' horizontal lifeline • Meets OSHA’s fall arrest requirements for anchors. Suitable for use in Class 1, Division 2 locations. • Specially designed suction cup system and vacuum technology attaches to structure without damaging the surface in any way. No holes or destructive and time consuming attachments are required. Ideal for use on planes, tanks or other structure where drilling or welding are not an option. • Incorporates a fail-safe back-up system with both visual and audio alarms for added worker safety • Back-up features provides hours of safety in the event the air-line is severed or interrupted. • Installation is quick and easy, simply position vacuum anchor pad assembly against surface, turn on the vacuum switch, wait for audible / visual indication of proper attachment, connect lanyard to vacuum anchor. The unique Vacuum Anchor system was designed to provide a unique means of attaching to structural surfaces to create a fall arrest anchor point without time – consuming attachment activities. The convenient carrying handle and lightweight design allows simple installation. The self contained vacuum anchor operates on shop air or on-board compressed air bottle so no special outside power sources are needed. To install, simply press vacuum anchor pad assembly up against surface, turn on vacuum switch, wait for gauge indication and connect lanyard to system. The design and ease of use with this vacuum anchor will give you maximum safety wherever you need to work. Once installed, and the gauge shows green , simply attach DBI/SALA’s Force2™ shock absorbing lanyard to the D-ring on the pads and to the back of your harness and you’re protected – free to perform your work duties safely! Configure two pads and a line as a horizontal lifeline system for added versatility and maneuverability. For removal, simply depressurize the pads by rotating the handle and relocate using the convenient carrying handle. The system is completely reusable and transportable from one work area to another. The vacuum anchor pads pivot to fit most flat or curved surfaces offering greater flexibility from surface to surface. Similar Models: |
| WSP home page | Products page | Suppliers page | Fall Protection | Previous page | Next page |