Self-Contained Eyewash Fixtures
• Eyewash unit delivers a minimum of .4 GPM for 15 minutes. (Section 5.3.2)
• Valve mechanism opens in one second or less; it stays open until manually closed. (Section 5.3.2)
• Supply with flushing fluid, ("potable water, preserved water, preserved buffered saline solution or other medically acceptable solution...") (Definitions, Section 5.1.1)
• Use a flow meter to test flow rate; use a test gauge to test flow pattern. (Section 5.4.7)
• Locate 10 seconds or 55 feet from contaminants or hazardous materials. Locate on same plane as the hazard, free of obstructions. (Sections 5.4.2, Appendix B5)
• Frigid conditions require the installation of freeze protection equipment. (Section 5.4.5)
• Required to be free of obstructions a minimum of 6" from the outside of the eyewash sprayheads. (Section 5.4.4)
• Use a Bradley test gauge (Model 269-1444) to check flow pattern.

KEY FEATURES:
Transparent tank allows solution level to be checked easily
High-visibility yellow, molded pedestal and tank
Vandal-resistant, patented design
7 gallons (60 lbs.) provides full 15-minute flush
Heater jacket available to prevent freezing
Complies with ANSI Z358.1-2004
OVERVIEW:
The On-Site (S19-921) portable eyewash is the most innovative gravity-fed eyewash currently on the market. Employing a patented design, the On-Site is the only eyewash on the market that uses just seven gallons of water combined with eight ounces of preservative that provides a full 15-minute flush, at the ANSI mandated flow rate and maintains a consistent height throughout the spray pattern until the last drop of liquid is depleted from the tank. The clear yellow polycarbonate tank offers an exclusive vandal-resistant design that makes worker safety a priority.
EMERGENCY FIXTURE FACTS
ANSI requires the visual inspection of self-contained eyewashes to be certain the tank is full and ready for use. ANSI Z358.1-2004 Section 5.5.3

ON-SITE® PORTABLE GRAVITY-FED EYEWASH
S19-921
• Hinged eyewash tray activates in one quick motion
• Stainless steel clamps secure the tank during transport
• Vandal-resistant unit; foreign objects cannot be introduced into tank because all openings are sealed once the tank is installed
• Seven-gallon tank is one of the lightest portable eyewashes on the market
• SEI and cUPC certified
Includes:
• Wall bracket (can also deck mount)
• S19-899 preservative kit (shown)
ON-SITE EYEWASH AND HEATER JACKET
S19-921 H
• Protects against freezing; down to -20°F (-29°C)
• Insulated heater jacket conceals a 121-watt heater
• Secondary thermostat prevents overheating if primary thermostat fails
• Requires 120-volt AC line
• All UL-listed components
• SEI and cUPC certified
ON-SITE HEATER JACKET RETROFIT KIT
S19-921 HR
• Heater jacket ships attached to tank
• No tools required

ON-SITE WASTE CART
S19-399
• High-visibility yellow
• Captures used fluid, 56-gallon capacity
• Tapered sump, easy to drain
ON-SITE WATER PRESERVATIVE KIT
S19-899
• Replacement cap
• Three liners
• One 8-oz. bottle of preservative
• Inspection tag

BRADLEY WATER PRESERVATIVE
S19-865
• 8-oz. bottle, four bottles per carton
• Universal - can be used with any portable unit, from 6-20 gallons
• Mix with potable water
• Prevents bacteria, fungi and algae growth for up to four months

KEY FEATURES:
Built-in carrying handles
Tire filler valve with 0-100 PSI air gauge
Pressure relief valve to prevent over pressurization
8' drench hose unless otherwise specified)
Chrome-plated brass eyewash
All items comply with ANSI Z358.1-2004
OVERVIEW:
Looking for a portable eyewash that will withstand corrosive materials in isolated locations, can be used on trucks or areas without plumbing that require a 15-minute flush? Bradley's stainless steel portable pressurized tanks resist corrosion, and offer several options for customers that are looking for an eyewash with a drench hose, or even a tank outfitted with a heater jacket to prevent freezing. Portable pressurized tanks are a versatile, corrosion-resistant solution, to provide an ANSI compliant fixture in remote or non-plumbed locations. Portable pressurized fixtures balance the volume of water with a predetermined amount of pressure to maximize the time and volume of solution that provides a flush. The portable pressurized eyewash offers the convenience of a portable unit, is sold in a range of sizes, and the heater jacket option offers flexibility to handle a wide range of applications.
EMERGENCY FIXTURE FACTS
ANSI guidelines require that emergency fixtures supply potable water, preserved water, preserved buffered saline solution, or an alternative medically accepted solution.
ANSI Z358.1-2004 Section 3, Definitions 5.1.1

HEATER JACKET RETROFIT KITS FOR PORTABLE PRESSURIZED EYEWASHES
• Jackets intended to prevent freezing; not to be used on fixtures with drench hose
• UL-listed components
• Plug into 120-volt AC line GFCI recommended
• Secondary thermostat prevents overheating
S19-671 HR
• Jacket for 5-gallon tank
S19-690HR
• Jacket for 10-gallon tank
S19-788HR
• Jacket for 15-gallon tank
OPTIONAL CART
S19-690A
• Four-wheel, stainless steel transport cart
• For use with fixtures without a heater jacket
BRADLEY WATER PRESERVATIVE
S19-865
• 8-oz. bottle, four bottles per carton
• Universal — can be used with any portable unit, from 6-20 gallons
• Mix with potable water
• Prevents bacteria, fungi and algae growth for up to four months

RETROFIT DRENCH HOSE
S19-430EH
• Single head drench hose
• Retrofits to most eye or eye/face wash fixtures
• SEI and cUPC certified NOTE: Hose not insulated against freezing.
FOOT TREADLE KITS
S39-395
• Includes all necessary fittings for attaching to wall-mounted eyewashes for hand or foot operation
S45-572
• Includes all necessary fittings for attaching to Bradley pedestal mounted eyewashes and combination showers for hand or foot operation
S45-620
• Same as S45-572, except designed for S19-310PVC shower only
S45-1314SS
• Stainless steel 304 foot treadle that includes all necessary fittings for attaching to Bradley pedestal-mounted eyewashes and combination showers/eyewashes for hand or foot operation
S45-1314SS16
• Stainless steel 316 foot treadle that includes all necessary fittings for attaching to Bradley pedestal-mounted eyewashes and combination showers/eyewashes for hand or foot operation
S45-1544
• Aluminum foot treadle kit for European models

EYEWASH HANDLE, BALL VALVE AND HARDWARE
S30-070
• Stainless steel handle
• Hardware
• 1/2" NPT stay-open ball valve
S30-072
• Stainless steel handle
• Hardware
• 1/2" NPT stay-open ball valve
• For stainless steel hinged dust covers only
S30-074
• Left-hand activation conversion kit for pedestal-mounted or combination fixtures
• Stainless steel handle
• Hardware
• 1/2" stay-open ball valve
S45-122
• Plastic handle
• Hardware
• 1/2" NPT stay-open ball valve

DUST CAPS
107-371
• Dust caps only
• Sold individually; two required per eyewash
• Approximately 1" x 1"
• Yellow plastic tether
S53-063
• Dual eye/face wash dust caps only
• Sold individually; two required per eyewash
• 2-1/4" x 1"
• Beaded chain tether
S53-310
• Eyewash dust cap
• Sold individually; two required per eyewash
• l " x l "
• Not for use with portable pressurized tank eyewashes

DRENCH HOSE SPRAY KITS
• Includes all necessary fittings and hanger for attaching hose to Bradley units to provide a body water drench
S19-430EH
• Drench hose spray kit that attaches to eyewashes
S19-430SH
• Drench hose spray kit for use with drench showers
DRENCH HOSE REPLACEMENT PART VALVES
S27-265
• Replacement valve
S19-787
• Replacement valve with drench hose sprayhead
SPRAY RING ASSEMBLIES
S05-127
• Spray ring only
• Can only be added to eyewash with cross-connection yoke
S39-397
• Eyewash and spray ring assembly with supply stem

HOSES
S89-002
• 8' yellow thermoplastic hose
S89-003
• Plastic handle
• 6' stainless steel hose
269-053
• 12' yellow thermoplastic hose
• Recoiling
269-054
• 25' yellow thermoplastic hose
• Recoiling
HOSE GUIDE BRACKET
140-226
• Drench hose guide bracket
• For deck-mounted applications
DRENCH SHOWER HANDLE FOR STANDARD UNITS
128-156A
• 24" pull rod only
• Standard pull rod shipped with non-barrier-free showers
128-156B
• 36" pull rod only

DRENCH SHOWER HANDLE FOR BARRIER-FREE UNITS
128-156C
• 48" pull rod only
128-156D
• 45" pull rod only
• Standard pull rod shipped with barrier-free showers
128-156E
• 57" pull rod only
128-156F
• 69" pull rod only
DRENCH SHOWER HANDLE FOR HEAT TRACE UNITS
128-156G
• 26" pull rod only
BOWLS
154-058
• 10" diameter impact-resistant plastic eyewash bowl
187-053
• 10" diameter stainless steel eyewash bowl

SPACERS
113-1159
• Stainless steel stem spacer
• For use in fixtures with stainless steel bowl
113-1185
• Black plastic stem spacer
• For use in fixtures with yellow plastic bowl
STEMS
EYEWASH FIXTURES ONLY
• S21-071 Brass
• S21-072SS304
EYEWASH WITH SPRAY RING FIXTURES ONLY
• S21-073 Brass
• S21-074SS303
• S21-075SS316